The belt melted to the plastic drive pully and I need to replace it. How do I remove it
SOURCE: on 98 intrigue water pump removal how do i clear the ps pully
Im not sure what engine you have since this information was not provided. But the Power Steering Pump pulley usually has some 'holes' on the pulley in which you can get a wrench through to loosen and remove the bolt.
SOURCE: How to change water pump (1997 sonoma)
The text below is from the GM Service manual 4.3L V6 Engine
Water Pump Replacement (4.3L)
Removal Procedure
Drain the cooling system. Refer to Draining and Filling Cooling System .
Loosen the water pump pulley bolts.
Remove the cooling fan and clutch assembly.
Tools Required
J 46406 Fan Clutch Wrench
Removal Procedure
Remove the upper fan shroud.
Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
Remove the fan clutch assembly.
Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
Remove the water pump pulley.
Remove the radiator outlet hose clamp from the water pump.
Remove radiator outlet hose from the water pump.
Remove the water pump mounting bolts.
Remove the water pump from the engine.
Remove the water pump gaskets.
Clean the water pump gasket mating surfaces.
Installation Procedure
Install the water pump gaskets.
Install the water pump to the engine.
Apply a sealer (GM P/N 12346004) to the bolt threads.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Install the water pump mounting bolts.
Tighten
Tighten the mounting bolts to 41 N·m (30 lb ft).
Install the radiator outlet hose to the water pump.
Install the water pump pulley.
Install the water pump pulley bolts.
Tighten
Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
Install the fan clutch assembly.
Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
Inspect the cooling system for leaks.
Testimonial: "Thanks I appreciate it"
SOURCE: 1997 Buick Lesabre Water Pump problem
THE POWER STEERING PUMP PULLEY --- ARRGGH...Not a problem.
The power steering pump is held by two bolts. Use a socket and remove the top bolt and loosen the bottom bolt. Be careful not to completely remove the bottom bolt. The PS pump will loosen up enough so that you can push it towards the firewall and you will JUST have enough room to remove the waterpump bolts. Its tight but it will squeeze out.
SOURCE: removing water pump on 97 grand prix gt. Power
no you have to go thru the holes in the front of the power steering pulley. Usually a ratchet with a deep 13mm socket will do to remove the 2 bolts located at 12 and 6 o'clock then you will be able to move it out of the way
SOURCE: I need to replace the cam pulley that drives the
if there is a dimple in the middle of the shaft, then you will probably need a pulley remover. make sure you havent missed any bolts that you have to go through little holes on the pulley to get to also. and also turn the pulley and look for any bolts that hold it on that are on the sides of the pulley, like a allen key bolt but on the side of the pulley that holds it on that way. i hope this helps
128 views
Usually answered in minutes!
×