Step by step instruction to remove the rear bumper cover on 2003 nissan maxima gle

To remove the rear bumper cover on a 2008 Nissan Quest, you can follow these general steps:

1. Prepare the Vehicle: Ensure that the vehicle is parked on a flat surface and the engine is turned off. Put on safety goggles and gloves to protect yourself during the removal process.
2. Locate the Fasteners: Look for the fasteners securing the rear bumper cover. They are typically located underneath the bumper cover, near the wheel wells, and along the bottom edge of the bumper.
3. Remove the Fasteners: Depending on the specific model and trim level, the fasteners may be screws, bolts, or plastic clips. Use the appropriate tools, such as a screwdriver or socket wrench, to remove the fasteners one by one. Turn them counterclockwise to loosen and remove them. Keep the fasteners in a safe place for reinstallation later.
4. Disconnect Electrical Connections (if applicable): If your Nissan Quest has any electrical connections, such as sensors or lighting, attached to the rear bumper cover, disconnect them carefully. Look for connectors near the edges or inside the trunk area. Gently detach the connectors by pressing the release tabs or using a flat-head screwdriver to release any locking mechanisms.
5. Release the Clips: Once the fasteners are removed, there may be plastic clips or tabs securing the bumper cover to the vehicle's body. Carefully pry or release these clips using a trim removal tool or a flat-head screwdriver. Take care not to damage the bumper cover or the vehicle's body.
6. Remove the Bumper Cover: With all the fasteners and clips released, gently pull or wiggle the rear bumper cover away from the vehicle's body. Start from one side and work your way to the other, ensuring that all connections and clips have been detached. Be cautious of any remaining electrical connections as you remove the bumper cover completely.

Please note that the exact steps and fastener locations may vary slightly depending on the specific trim level and optional features of your 2008 Nissan Quest. It's always recommended to consult the vehicle's owner's manual or a professional technician for more precise instructions tailored to your vehicle.
Take your time during the removal process to avoid any damage to the bumper cover or the vehicle's body. If you're unsure or uncomfortable performing the removal yourself, it's best to seek assistance from a qualified technician or a reputable automotive service center.

Larry, normally engines do not have to be taken out to change timing tensioners, the bumper assy., A/C condenser,radiator,etc is removed to get access. Best if you get yourself a manual.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

DIY Video VQ35DE Timing Chain Tensioner and Water Pump Replacement

NISSAN MAXIMA Timing intro MP4

1995 2001 Nissan Maxima 1 3 Water pump replacement

How to fix timing chain rattle Maxima Forums

Best you buy a workshop manual.

there are four bolts two on each side they should be 10 metric get a ratchet extension and 10 metric socket crawl under the car (you might have to jack it up some) on one side there are two bolts take them off and go on the other side and take them bolts off that puppy should come off in your lap.... if not you took out the wrong ones nah just kidding on that last one. It is easy and only takes a few minutes to do

open the hood-remove the retainers across the top of the bumper/grille-in the wheel wells remove the retainers that go into the bumper-pull the fender liners back and remove retainer inside that goes through the bumper into the fender-next remove the retainers across the bottom of the bumper cover-you should be able to pull it off-watch out for wires hooked to fog lights etc.-cheers denny

this job is not for a newbie. so here we go with instructions. i believe you posted under 2003 nissan maxima section for replacing plugs.
remove engine trim cover that covers manifold and valve cover.
remove ign coils on frt valve cover and remove and install new plugs
for rear bank plugs you would need to remove upper intake plenum. disconnect all necessary electrical connectors and vacuum lines. make sure you are aware where the vacuum hoses go for reinstallation.
remove ign coils on rear bank valve cover. remove and install new plugs.
reassemble all parts.

Remove felt cover in trunk area around light, remove securing nuts and unplug the unit, assembly is reverse, ensure you install the seal with it. Good luck

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

• Remove tire
• Remove brake caliper assembly
• Remove brake rotor
• Remove hub cap
• Remove cotter pin
• Remove wheel bearing lock nut & washer
• Remove wheel hub bearing from spindle

to install wheel bearing nut torque to 137 Ib to 188 Ib

"The bad news is that to be able to access the 3 other bolts that hold the light assembly together, you have to remove the front bumper. including the grill. It is really not that hard, but you should take your time to do it right and to make sure you put it back together the same way. To remove the bumber you must unscrew to screws that are located inside each wheelwell behind the cover. I found it easier to remove both front wheels and hold the car up in stands unfront. these are the only screws that you will find, two on each side. after that just remove the black self taping screws from the grill and then reach behind the grill and compress the tabs that hold the grill to the bumper. remove the grill and then keep removing the self taping screws until the bumper comes off. BE CAREFULL to not let the bumper drop as it still has your conner lights connected. you can disconnect the corner lights or just place something to support the bumper. Hope this helps you, If you take it to the dealer they charge a labor of about $250.00 plus parts." -http://www.nissanclub.com/forums/2004-2008-nissan-maxima-gen-6-discussion/237350-2004-nissan-maxima-se-headlight-bulb-replacement.html
check out other fourms on this website and others to find diagrams and more detailed instructions on how to change the headlight