Question about 2006 Infiniti FX35

Open Question

<!-- from fixya rte -->What fuse do I change for the rear wiper - 2006 Infiniti FX35

Posted by Anonymous on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does 2003 dodge durango have just one fuse & relay that operates both front & rear wiper motors


No there is not just one ,the rear has it's own fuse an relay . Fuse J - 20a in ( PDC ) power distribution center , relay should be in same box ! sorry don't have location number , can't find it !

Mar 16, 2015 | 2003 Dodge Durango

1 Answer

My front wipers washer and rear wipper wont work


change the motor ,its under the front wing

Jan 11, 2010 | 2000 Ford Focus

2 Answers

Rear Windsreen wiper motor runs continuousley in


The "stop" function is in the motor of the wiper...remove the fuse and call it a day...You shouldn't use it anyway the rear glass is "soft" in these cars and the wiper action will damage the glass over time.
Sorry :o(

Jun 14, 2009 | 2002 Volkswagen Passat

1 Answer

Rear Windscreen wiper not working Seat Ibiza 2003


smonahan, The rear wiper fuse is actually a circuit breaker. It will reset itself.
Your wiper arm has probably stripped were it attaches to the motor shaft. You can check by trying to move the wiper arm with your hand, if it moves back and forth, its stripped. A new wiper arm will be needed.
Try it and let me know.
Regards,

Feb 12, 2009 | 2002 Oldsmobile Bravada

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

1 Answer

Rear wiper does not work


check the rear wiper fuse in the fuse box or check the motor is connected correctly to the plug or check the motor earthing is well tightened to the chassis

Oct 30, 2008 | 1991 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6571 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...