Why caint i get the outside rear view mirrors to adjust on my 2001 b3000 mazda
When i try to adjust the outside mirrors , they will move a little and then stop, i can move the mirrors by hand, then they will work a little and then stop
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I hope this helps or at least you can see it as I have had problems posting pictures. If you can't see it just reply I will try to manually draw you a diagram. Good luck.
2001 Mazda B3000 SE Regular Cab 2WD 3.0 liter OHV V-6
Removal NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.
Remove the front door trim panel; refer to Section 501-05.
Remove the outside rear view mirror access water shield.
Remove the speaker.
Remove the screws.
Disconnect and remove the speaker.
Disconnect the outside rear view mirror electrical connector.
Remove the outside rear view mirror.
Remove the nuts.
Remove the outside rear view mirror.
Feed the outside rear view mirror wiring through the opening in the front door.
Mirror, Power — Outside Rear View
NOTE: This procedure applies to both RH and LH power outside rear view mirrors.
Removal
Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
Remove the wire clip.
Disconnect the power outside rear view mirror electrical connector.
Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
Installation
To install, reverse the removal procedure.
Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in).
Glass, Outside Mirror Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707)
Trim Cover Removal
Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
Remove the two outside rear view mirror inside mounting hole cover screws.
Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure.
Mirror Control Removal
Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
if you are talking about side mirrors, and you just had car to car wash, they may have washed em and moved them. try applying moderate pressure to the outside of each mirror, which should realign the gears running the mirrors in and out...
Glass, Outside Mirror—Town Car Removal and Installation
Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
Using a small flat-bladed screw driver or equivalent, move latch release to released position.
Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
Disconnect heater wire connectors and auto dimmer connector, if equipped.
To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car Removal and Installation
Disconnect battery ground cable (14301). Refer to Section 14-01 .
Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door
Front—Town Car Removal
Snap out two door pull strap retaining screw covers. Remove screws.
Remove three screws on front and rear side and center of front door trim panel (23942).
NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
Disconnect wiring harness and heated seat switch electrical connectors if equipped.
Remove the door trim panel.
Disconnect two electrical connectors.
Remove nut from outside rear view mirror mounting base.
Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
Remove screw from outside rear view mirror base.
Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.
Remove the front door trim panel; refer to Section 501-05 .
go to car-part.com for a used mirror. Page with * is cheapest seller.
Remove the speaker.
Remove the screws.
Disconnect the electrical connector.
Remove the speaker.
Remove the outside rear view mirror (17682).
Disconnect the power mirror wiring clips.
Remove the outside rear view mirror nuts.
Remove the outside rear view mirror.
Feed the power mirror wiring through the opening in the front door (20124).
----------------------------
SECTION 501-09: Rear View Mirrors
2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION
Exterior Mirror Glass, 2001 model
Removal NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001. NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar. All mirrors
Position the glass in the full up position.
Locate the notch at the bottom of the exterior mirror glass.
Release the exterior mirror glass.
Insert a long flat-bladed screwdriver in the notch.
Push the screwdriver into the notch until the glass is released.
Heated mirrors
Position aside the exterior mirror glass.
Disconnect the electrical connectors.
All mirrors
Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation Heated mirrors
Connect the electrical connectors.
All mirrors
Position the exterior mirror glass on the exterior mirror motor.
Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
On drivers side internal door handle there's a small, joystick and an up-or-down switch. the former moves the mirror while the switch selects which mirror. good luck !
There are two tiny motors in each mirror. one for up/down. One for side to side. They have jack screws (plastic) that fit into the motors.
You can manually put your hands on either side of the mirror and force adjust it. If you hear a ratcheting sound, the jack screws are OK. Then repeat with hands on top and bottom.
If you hear ratcheting and mirror stays where you stop it, that means one of the motors is bad. The motor assembly is available as a separate part.
------------------------------------------------------------------------------------- Mirror Motor—Crown Victoria, Grand Marquis Removal and Installation
Disconnect battery ground cable. Refer to Section 14-01 .
Remove outside Rear View Mirror Glass as outlined.
Remove Outside Rear View Mirror as outlined.
Remove two screws from outside rear view mirror motor.
×