Question about 1987 Toyota Camry

1 Answer

Low beams don t work but high beams work

R and lft fuses are good. Relay is good. Relay clicks whin i turn on low beams

Posted by Anonymous on

Ad

1 Answer

Lawrence Oravetz

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 10,548 Answers

Hi and low beams run on different fuses too. Check the low beam fuse. There might be a grounding strap not making good connection too.

Posted on Aug 28, 2014

Ad

5 Related Answers

Anonymous

  • 2 Answers

SOURCE: Headlights

I READ ONLINE THAT THERE WAS A RECALL ON THIS YEAR AND MAKE, CHECK WITH TOYOTA WEB SITES TO RECTIFY YOUR PROBLEM

Posted on Jul 25, 2008

Ad
keemo68

Ronald Mueller

  • 1263 Answers

SOURCE: Headlight 2004 camry

your module in the steering wheel is faulty you should get it replaced. you can purchase it at ie Napa for alot less than through a dealer.

Posted on Sep 01, 2008

Anonymous

  • 1 Answer

SOURCE: Low beam headlights don't work

I know this is not your problem, but my low beam stopped working, both bulbs failed, no burn marks or broken element. Just had to tell someone

Posted on Mar 24, 2009

tsuperfrugal

  • 23 Answers

SOURCE: Headlights won't turn on

Try following the ground wire from the bulb to where it makes its ground. remove the ground connection, clean the terminal, the ground point where it makes a connection and reassemble it all. Sometimes you have power being delivered but the ground side isn't providing a good path for the current.

Posted on Jun 10, 2009

ourhowse

Dar

  • 2007 Answers

SOURCE: 2001 Toyota Corolla high beam lights are not

Your switch must be working since your indicator is telling you when the high beams are on, so my guess is that your bulbs are faulty. The high beam part. They probably burnt out one at a time, so you didn't notice until the second one went. Change your bulbs, and see if that solves it. If not, let me know.

Posted on Jul 23, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chevy malibu no signal at relay for low beam lights. Switch is good


Your best bet , take your vehicle to a qualified repair shop . Before you want to replace the BCM . . Professional tech would check for DTC'S - diagnostic trouble code's in the BCM before replacing part's that are not needed .

No signal at signal wire on relay ???? Which circuit wire mite that be ? Hooking up a factory or professional scan tool to view input data from the switch would also be a good step .

Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Headlamps Inoperative - Low Beams
Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference: Master Electrical Component List
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle
2
Place the headlamp switch in the HEADLAMP position.
Place the headlamp dimmer switch in the LOW position.
Do the low beam headlamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Disconnect the turn/headlamp switch connector C2.
Connect a 15-amp fused jumper between the headlamp low beam signal circuit and a good ground.
Do the low beam headlamps illuminate?
YES - Go to Step 4
NO - Go to Step 5
4
Inspect for poor connections at the harness connector of the turn/headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
5
Repair an open or high resistance in the headlamp low beam signal circuit. Refer to Circuit Testing and Wiring Repairs .
YES - Did you complete the repair?
NO - Go to Step 7
--
6
Replace the turn/headlamp switch. Refer to Turn Signal Multifunction Switch Replacement .
YES - Did you complete the replacement?
NO - Go to Step 7
--
7
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
No - Go to Step 2

It's more then likely the dimmer switch .

DTC B2575
Circuit Description
The body control module (BCM) turns on the LOW BEAM relay when the ambient light sensor senses a dark condition or the low beam headlamps are requested ON. Battery positive voltage is supplied to the LOW BEAM relay at all times. The BCM grounds the LOW BEAM relay control circuit in order to activate the relay.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2575 Headlamp Control Circuit

B2575.01
Will set if there is a short to voltage in the low beam relay control circuit.
B2575.06
Will set if there is an open or short to ground in the low beam relay control circuit.

Jul 16, 2018 | Cars & Trucks

1 Answer

2011 HHR headlights not working. No high or low beam . Any ideas?


Do you know how to test electrical circuit's using a wiring diagram an a voltmeter ? Reading how the headlamps are suppose to work ,then testing is how to find the problem .
Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the BCM supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine . Under system click on lighting , then under subsystem click on headlamps . Click the search button ,then the blue link .

Video's on youtube on electrical testing

Jun 16, 2018 | Chevrolet HHR Cars & Trucks

1 Answer

Is there any fuses or relays that are not in the fuse box on a 2002 buick rendezvousfor the bright lights


The high and low beam lights use the same power source, so if the low beams work the high beams have power.
There is a low and high beam relay controlled by the dimmer switch.
If the low beams work and the high beams don't, and the bulbs are good, check the dimmer switch and the high beam relay.

Aug 04, 2012 | Buick Rendezvous Cars & Trucks

1 Answer

Click headlights to low beam and no lights work on high beam


I'm not sure exactly what your problem is. When you "click" your lights to low beam, your high beams should not work. But if your low beams work when you "click" them on, but your high beams don't work when you "click" them on, you either have a blown fuse, bad relay or high beam elements burned out on both lamps. (Not so unusual) Possibly a bad "dimmer" stalk switch or bad wiring, too, but a little less likely.

Sep 05, 2011 | GMC K1500 Cars & Trucks

1 Answer

2005 Dodge caravan. The Headlights are not staying on. When we turn the switch, sometimes they come on, sometimes they do not. It's getting worse.


Hello, on the van you have a high beam fuse and relay. On the low beam you also have a fuse and relay. Check the fuse/relay panel for a blown fuse controlling the low beam lights. If you do not find a blown fuse have some one to turn the key on and turn on the high beam lights. During this time locate the low beam headlight relay and place your finger on top of relay, have the other person to switch from high beam to low beam lights. You should feel a click in the relay when they make the switch from high to low beam. If not replace the relay and the problem should go away. Hope this will help you.

Thanks

Aug 14, 2010 | 2005 Dodge Caravan

1 Answer

I have a 2005 dodge caravan. the headlights have


On the van you have a high beam fuse and relay. On the low beam you also have a fuse and relay. Check the fuse/relay panel for a blown fuse controlling the low beam lights. If you do not find a blown fuse have some one to turn the key on and turn on the high beam lights> During this time locate the low beam headlight relay and place your finger on top of relay, have the other person to switch from high beam to low beam lights. You should feel a click in the relay when they make the switch from high to low beam. If not replace the relay and the problem should go away. Hope this will help you.

May 28, 2010 | 2005 Dodge Caravan

1 Answer

Inop low beam fuses are good makes clicking sound when you turn them on high beams work fine


Low beam has a relay it is making the sound, turn on while looking for the noise the relay you find may be bad but make sure the the low beam bulbs are good first as they are way more likly to be bad than the relay or the fuse

Oct 12, 2009 | 2002 Honda CR-V

1 Answer

Kia Optima 2005. no low beams


Check the low beam relay . Look here for location http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine size. Under system click on electrical distribution , then under subsystem click on relay . Click the search button then the blue link . Look at left side near the bottom ,HEAD LP LO . Right above #5 and #4 fuse's . Do you know how to test at relay base ,that's where it plugs into. Watch this video .
VEHICLE RELAYS Operation Diagnosis

Aug 16, 2017 | 2005 Kia Optima

Not finding what you are looking for?
1987 Toyota Camry Logo

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...