Question about 2004 Ford F250

Open Question

Why is my v10 cutting off when put into gear - 2004 Ford F250

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My v10 excursion overheated going up a hill, I quickly pulled over and the car turned off. After an hour we checked gauges all was good so we started truck. Knockign started when put in gear and gas.


Sounds like the bottom end went out in the motor. Whoever tried to tell you the oil shifted is full of garbage. The oiling system is pressurized and designed to not starve the engine of oil under normal use. Proving that a quick lube place is responsible for engine damage is nearly impossible which is why many people won't use them. If you do you have to inspect the fluid levels and check the filter and drain plugs yourself. Every time before you accept the vehicle back and sign anything. Sorry to say it sounds like you may be spending big $$ to fix your ride. It's possible that the bottom end can be redone but since it ran hot I would not risk it. With aluminum cylinder heads it only takes one time of running hot to cause damage to the top end of the motor.

Oct 20, 2016 | Ford Cars & Trucks

2 Answers

When you put in gear cuts off


Need year make and model info to render any help

Apr 12, 2015 | Cars & Trucks

1 Answer

2000Ford f 250 with a v10 is cutting out in misfiring


I discovered the REAR coil & spark plug on the passenger side somehow was full of water. It seems its a common trend in the 5.4 and the V10 that the rear plugs and/or the coil over plugs go bad because of water dripping in from the cowel.

After purchasing your new coils and plugs it is a simple job, Its just very Time comsuming it get the plugs removed and replaced. you should be able to figure it out quickly. ALSO new coils come with a new boot.

Apr 24, 2014 | Cars & Trucks

1 Answer

Car cuts when put into gear


Dirty fuel filter,too low,low idle,dirty throttle body.

Apr 06, 2014 | 1995 Ford Contour

1 Answer

2000 chrysler concorde starts up then cuts off when put in gear. starts back up only with a jump, then cuts off when put in gear. What is the problem?


Could be a faulty torque converter but that would not explain having to use a jumper. Have you let the engine run for 5 or 10 min before shifting into gear ?

Jan 21, 2014 | Cars & Trucks

1 Answer

2001 dodge ram 2500 v10 oil pressure drops to 0 then back up


you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

May 18, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

F350 fuel pump relay 2004 gas v10


check for power to the pump first ,then if it has power check for earth ,could be immobilisor has cut in..when checking for power to pump use a seperate earth for the meter ,because if the immobilisor cuts in it stops the earth to the relay stopping it from working

Dec 24, 2009 | 2004 Ford F350

1 Answer

I have a 2002 ford excursion 4x4 v10 it starts but when you put in gear it dies what could it be.


ck trans fluid level. if its low, it could cause this. or the IAC (idle air control) valve is faulty.

Oct 14, 2009 | 2002 Ford Excursion

1 Answer

Truck cuts off when put in gear


If its the 4JX diesel engine the crankshaft position sensor wants an adjustment as its going out of range.

Apr 19, 2009 | 2002 Isuzu Trooper

Not finding what you are looking for?
2004 Ford F250 Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...