Question about 1995 Dodge Caravan

Open Question

HOW TO REPLACE A FRONT TUEN SIGNAL LENSE ON A 1995 DODGE CARAVAN?

Posted by Anonymous on

Ad

5 Related Answers

SOURCE: tensioner pulley 1995 dodge caravan

Hi my name is Allen!

To help you I need to know what engine you have?

For example; 3.0 liter or 3.3 liter

If it is the 3.0 liter the nut for the tensioner is toward the firewall side of the engine tucked tightly under the exhaust manifold, very hard to get too.

If its the 3.3 liter you would have already seen it, both have only one nut holding the tensioner on. This one is easier.

For further assistance contact me at FixYa!

Posted on Dec 28, 2008

Ad

Anonymous

  • 92 Answers

SOURCE: Replace front struts 1994 Dodge Grand Caravan

your on the right track. it can't be done with out a spring compressor. but do you purchase a GOOD
SAFE compressor for a few uses ?. better to unbolt the three top 13 mm retainer nuts ,than unbolt the two 21 mm lower steering knuckle bolts along with the 15mm stabilizer nuts, and take the strut to a local garage and pay a couple of bucks and have someone pressthe spring on thier compressor for you . its safer. also index the lower 21 mm knuckle bolts for reassemble. its your wheel alingment camber angles.
good luck chris

Posted on Mar 14, 2009

Ad

Anonymous

  • 95 Answers

SOURCE: Replace the front wiper motor 2000 Grand Caravan Dodge

It is on the firewall under the hood. It has 3 to 4 bolts holding on. Be careful when taking it out to see how the new one lines back up. Hope it helps.

Posted on Mar 30, 2009

Anonymous

  • 69 Answers

SOURCE: Need to replace the heater core in a 1995 Dodge Grand Caravan SE

1991-95 Models

  1. Disable the air bag system by disconnecting the negative battery cable.
  2. Have the system discharged by a qualified professional mechanic using an approved recovery/recycling machine.
  3. Drain the cooling system.
  4. Remove the steering column cover and left and right side under panel silencers.
  5. Remove the center bezel by unclipping it from the instrument panel.
  6. Remove the accessory switch carrier and the heater/air conditioning control head.
  7. Remove storage bin and lower right instrument panel.
  8. Disconnect the blower motor lead under the right side of the instrument panel.
  9. Remove the right side 40-way connector wiring bracket.
  10. Remove the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  11. Disconnect the vacuum lines at the brake booster and water valve.
  12. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
  13. If equipped with air conditioning, remove the H-valve and condensation tube.
  14. Disconnect the temperature control cable and vacuum harness at the connection at the top of the unit.
  15. Remove the retaining nuts from the package mounting studs at the firewall. Disconnect the hanger strap from the package and rotate it aside.

To install:
  1. Remove the temperature control door from the unit and clean the unit out with solvent. Lubricate the lower pivot rod and its well and install. Wrap the heater core and/or evaporator with foam tape and place in position. Secure with the screws.
  2. Assemble the unit, making sure all vacuum tubes are properly routed.
  3. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  4. Connect the hanger strap from the package and rotate it aside. Install the 2 brackets supporting the lower edge of the heater housing. Connect the blower motor wiring, resistor wiring and the temperature control cable.
  5. Install the retaining screws from the right side to the steering column. Install the instrument panel trim covering and reinforcement.
  6. Assemble the unit, making sure all vacuum tubes are properly routed.
  7. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  8. Connect the hanger strap from the package and rotate it aside. Connect the blower motor wiring and temperature control cable.
  9. Install the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  10. Install the right side 40-way connector wiring bracket.
  11. Install the lower right instrument panel and storage bin.
  12. Install the heater/air conditioning control head and accessory switch carrier.
  13. Install the center bezel to the instrument panel.
  14. Install the under panel silencers and steering column cover.
  15. Install the vacuum lines at the brake booster and water valve.
  16. Connect the heater hoses to the core tubes.
  17. Using new gaskets, install the H-valve and connect the refrigerant lines. Install the condensation tube.
  18. Have the system evacuated and recharged by a qualified professional mechanic, utilizing the proper equipment. Add 2 fl. oz. (59 ml) of refrigerant oil during the recharge. Fill the cooling system.
  19. Perform the Air Bag System Check procedures outlined in this section before connecting the negative battery cable.
  20. Connect the negative battery cable and check the entire climate control system for proper operation and leaks.

Posted on Apr 08, 2009

Anonymous

  • 92 Answers

SOURCE: How do I replace the right rear turn signal bulb

Raise tailgate. Pry under head of fastner with flat bladed small screw driver. Otherside hook shaped, In rubber grommet. Roll away from fastner side.Disengage red lock tab then press release tab.

Posted on Sep 27, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 grand caravan turn signal


CHECK FOR ANY TUEN SIGNAL LIGHTS THAT ARE NOT WORKING AND REPLACE THEM

Feb 12, 2013 | 2006 Dodge Grand Caravan

2 Answers

1995 Dodge Dakota signal light and brake lights quit


I had the same problem that the brake light / turn signal on the right side didn't work (in the 2006 Dodge Caravan it's the same bulb). After a long search I found the problem: There was corrosion on the contact of the bulb assembly. After scraping off the corrosion everything works now.

Dec 20, 2011 | 1995 Dodge Dakota

1 Answer

How to replace the rear hatch brake light on a 2001 dodge grand caravan


If you are referring to the Third Brake Light mounted at the top of the rear hatch, then there should be 2 screws on either side of the lense. Remove those two screws and pull the lense off. You can now twist the bulb socket counter-clockwise and remove it from the lense.

Jan 21, 2011 | 2001 Dodge Grand Caravan

1 Answer

1999 dodge grand caravan; how do you replace the rear turn signal bulb?


If you are Replacing the REAR BULB Look Along the RUBBER SEAL FOR 2 SCREWS and REmove them this will Free the INTIRE TAIL LIGHT and Give you Access to the Bulbs.it is self Explanitory After this. If it is THE FRONT BULB Open hood and Look at the top of Headlight Lense Just Behind it but On TOP and REMOVE the 1 10mm Bolt to Free the Intire HEADLIGHT and you will See the Turn Sygnal BULB on the OUTSIDE END of the HEADLIGHT LENSE and It TOO Is self EXPLANITORY.

Jul 16, 2010 | 1999 Dodge Caravan

1 Answer

1995 dodge caravan-need to drain fuel mtank and then drop it to replace bad fuel pump. How?


1995 and before has a siphon port at the rear of the tank. 1996 and later has to be drained with the fuel pump, or by removing filler hose.

May 19, 2010 | 1995 Dodge Caravan

1 Answer

1995 dodge caravan low beam headlights don't work but high beams do,bulbs are ok put new dimmer switch in they still don't work


look into the actual headlight switch and the wiring and the turn signal switch nand wiring

Apr 29, 2010 | 1995 Dodge Caravan

1 Answer

Replacing front signal bulb


Prise out the lense cover very carfully, there are lugs on each side of it that break very easly!
The bulbs are then easy got to.

Mar 24, 2010 | 1995 Jaguar XJ6

1 Answer

How do I change rear turn signal bulb on 02 Grand Caravan?


open the rear hatch,there are two screws holding each taillight assembly in,remove the two screws for the side you want off,pull out on side of lens assembly where the screws were,un hook the outer side when you swing it out,

Jan 06, 2010 | 2002 Dodge Grand Caravan

1 Answer

How to access and replace turn signal bulb?


Remove the headlamp assembly, and replace the bulb. Should be one or two bolts on the top holding it in, then a couple of push joints to pull out.

Mar 08, 2009 | 1998 Dodge Grand Caravan

1 Answer

1995 dodge caravan


YOUR LOW PORT IS AT THE FIRE WALL NEXT TO THE WINSHIELD AREA ON THE PASSENGER SIDE.

Jul 10, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
1995 Dodge Caravan Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...