Question about 2004 Proton Gen-2

1 Answer

I have GEN-2 if i press the brake pedal all ligths on what is the posible problem?

When i press the breake pedal park ligth also on. i change the breke pedal switch but still have the problem any body have this problem befor pls help me.. tnx

Posted by rose wayne on

Ad

1 Answer

lensman365

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

It can only be a problem caused by a shortage, the wire activated by the brake as you apply the brakes is shorting ( touching) the other wires in the wiring loom, hopefully not too far down , unless you are competent and confident with a cars electrical circuit I would seriously suggest you get an auto electrician. B4 that Have a look and follow the brake pedal wire ( situated maybe on the floor of the car and activated as the brake pedal is pressed or on the pedal itself, )look for anywhere tge wire is bare ( without insulation ) then rectify and all should be OK , If you cannot see an easy fix get an auto electrician, get a call out , not a auto shop /garage he will be cheaper.

Posted on Aug 02, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the brake ligths?


Did you check to see if there is a fuse on the brake lights circuit?

If you changed the lamps and the brake switch it is obvious that they are not being energized.

Aug 31, 2015 | Cars & Trucks

1 Answer

Check ligth braek and battery ligth


If you can,go to Autozone,they will test your battery and alternator for free,only takes a few minutes,on your brake light,check brake fluid in master cylinder could be low, setting the sensor off.If your brake fluid runs dry,you will have to bleed,you may have a brake leak and check your brake pad and shoes,may need replacing.

Dec 24, 2012 | 1999 Isuzu Trooper

1 Answer

My 05 sts driver side break ligth dont work


Never push the brake pedal down when the spring brakes are on. If you do, the brakes could be damaged by the combined forces of the springs and the air pressure.


----------------------------------------------------------
FGTech Galletto 2-Master EOBD2

Dec 18, 2012 | 2005 Cadillac STS

1 Answer

HAVE TO PRESS REAL ******* BRAKE PEDAL TO GET OUT OF PARK


I suspect your brake ligth switch is broken or out of adjustment. It is on the brake pedal arm.

Aug 23, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

Car will not shift in reverse from park ,I have pressed on brake but it will not come out of park.


When you press the brake do the brake ligths come on?If not you have a bad brake light switch.

Apr 14, 2011 | 2000 Ford Taurus

1 Answer

My rear brake light and signal light do not work. I change the bulb but it did not work


There is break switch top of brake pedal with two wires conector.Bridge them and check ligths.There must come positive in one of wires.

Nov 30, 2009 | 2005 Ford Explorer

1 Answer

MY BRAKES LIGTHS ARE NOT WORKING.......


if ALLyoure brake lights are not working i would definately check the brake swich usually located on the brake pedal itself up under the lower dash area

Apr 25, 2009 | 2000 Ford Expedition

1 Answer

My break ligths dont flash


Unless both bulb filaments went out, there is a switch that the brake pedal sits on when released. It should be located under the dash above your foot. You shouldn't miss it. When the brakes are applied, the switch pops out activating the lights, it sounds like that switch may be faulty. Hope that works

Feb 14, 2009 | 1992 Buick Roadmaster

1 Answer

My 1994 honda accord break lights wont turn off when car has stop


brake in a car is verry important for your saffety and others. that why they install many devices or systems to control them and make shure they work propely 1; brake light switch on the pedal floor(to indicate to the folowing car that you are stoping) 2;brake sensor fluid level (on the brake master cylinder under the hood)
to monitor the level of the fluid in the reservoir 3; brake pressure sensor (on the brake dispencer under hood) will warn you in case of brake pressure faillure .note, it may be more sensors, depending on the make of the vehicle but this is the tree comon causes for brake ligth to stay "on"

Dec 25, 2008 | 1994 Honda Accord

1 Answer

Stop ligths


There is a possibility that the brake light switch that is located at the upper part of the pedal has gone bad.

Jun 24, 2008 | 1988 Toyota Corolla 4 Door

Not finding what you are looking for?
2004 Proton Gen-2 Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proton Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

gbob59

Level 3 Expert

3063 Answers

john h

Level 3 Expert

23515 Answers

Are you a Proton Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...