Question about 2008 GMC Canyon 2WD

1 Answer

Why does my GMC Canyon 2008 Blower fan only works on 2?

Blower fan only works on 2?

Posted by Anonymous on

Ad

1 Answer

pat manning

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 71 Answers

I had a problem on my 2006 sierra, the fan wouldn't work on 5. gm had a curtisy recall, they had to replace a resistor, at no charge, last week. Ask your dealer about any recall for this with your vehicle.

Posted on Aug 08, 2014

Ad

5 Related Answers

alpha4

Dale Ellenberg

  • 42 Answers

SOURCE: 2004 gmc canyon fan moter for ac dont work

There is a fuse I would check first if you haven't tried that yet. They had problems with the switches in some of those vehicles. If you could take the control out and unpug then reattach the plug it may start working meaning the switch is bad.
You may have a bad fan motor. Do you have a test light to check for voltage at the motor itself?
Lastly, there is a resistor set that changes from low to high that may have one or more resistors burned out.
Dale

Posted on Dec 23, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: Fan blower motor

The Canyon has an inherint problem with the Fan Power cable being loose. When I say loose...I'm saying that you need to adjust the wires and then take a zip strip to tighten it up.

Passenger side under the dask are 2 cable hook ups. the one on the farthest right (Only 2 wires going to the plug) is the fan power cable. Jiggle it while the fan is on position number3 so you can hear when it comes on!!!

Posted on Mar 11, 2009

roniecon

Ronny Bennett Sr.

  • 6927 Answers

SOURCE: fan control only works on high

Replace the blower motor resister,it is mounted right next to the blower motor,it has a lug with about 7 wires on it.Just unplug it and remove two screws to remove the resister.This controls the speeds for the blower motor.The blower motor is the cause of the resister failure.Even if the motor seems to sound,and run fine,it is pulling to many amps.

Posted on Dec 08, 2009

Anonymous

  • 1 Answer

SOURCE: heater fan only works on the high position?

There is a plug up under the glove box that loosens and you need to snug it up.

Posted on Feb 04, 2010

skychief2001

Stephen

  • 21873 Answers

SOURCE: 2003 GMC Yukon XL blower fan intermittently doesnt turn on

Could be the blower motor, the resistor, or the control on the dash.
You'll need to check the circuit for voltage when it fails to work.

Posted on Aug 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Isuzu Rodeo 2.6 Blower Fan not working


need to replace the resistor should sit by the blower or close by

Feb 20, 2013 | Cars & Trucks

1 Answer

Location of 2003 Honda accord blower motor


Check to see if u have power & ground to the blower with the fan on.if so u need A blower mtr

Aug 13, 2017 | 2003 Honda Accord

2 Answers

VW Golf 2000 A/C and Fan Blower problem


In most cases, the problem related to blower and A/C switch lies with the fan controller relay which is fitted on the housing of the blower. It is a small circuit board and your fan is connected through this circuit relay and it controls the speed of the fan which further due to safety circuit controls the A/C. indirectly. Check that.

Apr 14, 2012 | 2000 Volkswagen Golf

2 Answers

I have a 2002 protege a/c wont work on all blower speeds and my friends 2000 blower will only work on 2 settings


Replace fan switch in dash.Or may even just need connections cleaned with some wd/40. To replace switch you need to remove dash and knob's, Then you have a switch that has the wires from fan to connector. . If these are ok and clean you need to replace your blower motor, Best of luck to you.
.

Apr 04, 2011 | 2003 Mazda Protege

2 Answers

Heater blower stopped working?


Hello,
You may want to try your fan on all speeds. If it will work on high, you have a bad resistor for the fan motor. ( high speed doesn't go through the resistor ).
If it doesn't work on any speed, I would check the following;
1. Make sure the fuse isn't blown for the fan blower motor.
2. Check, or have checked the wires between the fan control switch and the fan blower motor.
3. Have the fan control switch checked.
4. Have the fan blower motor checked.

I hope this helps you.

Feb 03, 2011 | 2002 Buick Rendezvous

1 Answer

2004 sierra, fan blower stopped, not the fuses. where is the fan blower switch and how do I replace


get a voltmeter; check for 12vdc at the blower motor with the blower turned on; if there is voltage, the blower motor is bad; should be located behind a panel underneath the dash on the passenger side; if the fan works on 1 or 2 speeds, it is probably the blower resistor located in the same area as the blower; u can check utube for details

Jun 27, 2010 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

Where is the fan in a 2000 dodge caravan


I am assuming you are asking about the Blower Fan and not the Radiator Fan?
The Blower Fan is located below the Passenger side Dash. It is inside the black Duct work.
May I ask what the problem is?
Is the Blower working or only working on High? If only on High then the Blower Motor is fine and the Blower Motor Resistor that controls the Low to High speeds is bad. This is located behind the Glove Box in the Dash and on the firewall. Remove the Glove Box to access. It is approximately 3 1/2 inches by 1 1/2 inches and has 3 to 4 wires going into it.
There is also a Front Blower Motor Relay located in the Relays and Fuses.
Before replacing the Blower Motor, get back with me (for free) and let me know. This may save you alot of money in the long run, saving you from purchasing parts you may not need!
Let me know if this helped, and let me know what the problems (symptoms/signs) are.
Contact me in the Comment Section of your Posted problem.

Feb 02, 2010 | 2000 Dodge Caravan

2 Answers

Heater blower is not working in 1, 2, 3 and fan


MY 2003 MALIBU AC WORK VERY COOL FOR ABOUT ONE HOUR AND THEN TURN A BIT HOT AND THEN NO AIR COME OUT WHY I HAVE CHECK THE FREON AND ITS OK .

Nov 22, 2009 | 2003 Chevrolet Malibu

2 Answers

Blower fan resistor module replaced, worked for 2 days quit again


HIGH RESISTANCE IN THE BLOWER MOTOR CAN CAUSE YOUR PROBLEM, OR A BAD RESISTOR.
THERE IS NO REAL GOOD WAY TO CHECK THE RESISTANCE OF THE BLOWER MOTOR.

Jul 16, 2009 | 2005 Chevrolet Malibu

1 Answer

Blower motor stop working on 2000 Pontiac GP


Two possibilities I can think of. #1. The blower motor itself is dead, or #2. The blower motor resistor is fried. Blower motor resistor, however, is more known for taking out certain fan speeds, such as the lower fan speeds.

Dec 28, 2008 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
Cars & Trucks Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...