My wiper not worked.

Did you check fuse's & relays ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multi-function switch is in the ON or intermittent position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (15A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multi-function switch is turned to the OFF position. The SJB receives inputs from the multi-function switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the park position. An internal switch in the rear wiper motor then moves to the run position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the park position, the internal switch in the rear wiper motor moves back to the park position. If the multi-function switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multi-function switch is in the intermittent position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again. The SJB is the smart junction box .(computer )

Rear Washer System
The SJB supplies power to the rear washer pump from fuse 21 (15A) when the ignition switch is in the ON or ACC position. The rear washer pump receives ground from the multi-function switch when the wash function is turned ON. The multi-function switch also signals the SJB when the rear wash is activated and the SJB then activates the rear wiper.

Do you know how these wipers Work / what controls them ? Do you know what a smart junction box is ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multifunction switch is in the ON or INTERMITTENT position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (10A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multifunction switch is turned to the OFF position. The SJB receives inputs from the multifunction switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the PARK position. An internal switch in the rear wiper motor then moves to the RUN position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the PARK position, the internal switch in the rear wiper motor moves back to the PARK position. If the multifunction switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multifunction switch is in the INTERMITTENT position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again.

Do you know what DTC'S - diagnostic trouble codes are ?
Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1244 Wiper Rear Motor Run Relay Coil Circuit Failure SJB If the rear wiper is inoperative, Go To Pinpoint Test B . If the rear wiper is always ON, Go To Pinpoint Test D . B1245 Wiper Rear Motor Run Relay Coil Circuit Short to Battery SJB Go To Pinpoint Test B . B1614 Wiper Rear Mode Select Switch Circuit Failure SJB Go To Pinpoint Test D .
Did you have it checked for DTC'S ?

Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Did you check for voltage at the wiper fuse? My info says that fuse is hot all the time. Use a digital multimeter. Everything off, take a reading across battery posts, the generic spec for a full charge is around 12.6 volts. You should get close to same reading at the wiper fuse, hopefully. When checking voltage at the fuse, use chassis ground not the other leg of fuse. There are wiper relays, those are pcb relays, they are soldered into the fuse box, you can't pull them out. Your bcm is also involved with those relays. Your multifunction switch basically tells the bcm you turned on your wipers, then the bcm controls voltage or ground for the relays. You can see wire color for hi and lo speed voltage. Maybe a problem with fuse box or wiring circuit if voltage is low? I hope this was of some help?

If the wipers work on normal setting, would not be a relay problem. The intermittent wipers and the washer motor are separate issues-if all on the same stalk, it is probably a bad switch. Hot wire the washer motor with jumper wires to check motor operation. The motor is probably mounted on the bottom of the washer fluid reservoir. Good luck.

Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper RUN/PARK relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect senses magnet to turn off RUN/PARK sense the output to the windshield wiper RUN/PARK software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.

• The intermittent windshield wiper speed does not operate correctly

• Multifunction switch.
• Circuitry.
• Windshield wiper motor.

• Go To Pinpoint Test D .

Pinpoint Test D: The Intermittent Windshield Wiper Speed Does Not Operate Correctly
Normal Operation During normal operation, the windshield wiper motor receives voltage at all times through battery junction box (BJB) fuse 1 (30A), circuit 65 (DG). The windshield wiper motor also receives power with the ignition switch in RUN or ACC positions through central junction box (CJB) fuse 33 (15A), circuit 1002 (BK/PK). Ground is provided to the windshield wiper motor through circuit 676 (PK/OG) and circuit 57 (BK). The run/park and high/low relays are contained in the wiper motor electronics. Mode of operation is dependant on the signal(s) received from the multifunction switch.

Possible Causes
• Multifunction switch
• Open in circuit 57 (BK), 56 (DB/OG), 61 (YE/RD) or 63 (RD)
• Windshield wiper motor

PINPOINT TEST D: THE INTERMITTENT WINDSHIELD WIPER SPEED DOES NOT OPERATE CORRECTLY Test Step Result / Action to Take D1 CHECK THE MULTIFUNCTION SWITCH

• Key in OFF position.
• Disconnect: Multifunction Switch C202b.
• Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  
• Did the multifunction switch pass the component test?

Yes
GO to D2 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . TEST the system for normal operation. D2 CHECK CIRCUIT 57 (BK) FOR OPEN

• Measure the resistance between multifunction switch C202b-6, circuit 57 (BK), harness side and ground.
• Is the resistance less than 5 ohms?

Yes
GO to D3 .

No
REPAIR the circuit. TEST the system for normal operation. D3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD) AND 63 (RD) FOR OPENS

• Disconnect: Windshield Wiper Motor C125.
• Using the following table, measure the resistance between multifunction switch C202b harness side and windshield wiper motor C125 harness side:
  
  Multifunction Switch C202b Windshield Wiper Motor C125 Pin 2, circuit 56 (DB/OG) Pin 10, circuit 56 (DB/OG) Pin 4, circuit 61 (YE/RD) Pin 1, circuit 61 (YE/RD) Pin 1, circuit 63 (RD) Pin 9, circuit 63 (RD) Pin 3, circuit 58 (WH) Pin 11, circuit 58 (WH)
• Is the resistance less than 5 ohms?

Yes
GO to D4 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. D4 CHECK FOR CORRECT WIPER MOTOR OPERATION

• Disconnect all wiper motor connectors.
• Check for:
  • corrosion.
  • pushed-out pins.
• Connect all wiper motor connectors and make sure they seat correctly.
• Operate the system and verify the concern is still present.
• Is the concern still present?

Yes
GO to D5 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. D5 CHECK THE WINDSHIELD WIPER MOTOR

• Key in OFF position.
• Disconnect: Windshield Wiper Motor C125.
• Carry out the windshield wiper motor component test as outlined in this section.
• Did the windshield wiper motor pass the component test?

Yes
The system is operating correctly at this time. Concern may have been caused by incorrect binding pivot arm adjustment. REFER to Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

As the intermittent wipers are based on resistance, try the easiest fixes first:1. Disconnect the negative terminal on the battery. Pull the relays for the blower motor and both wiper relays and the 30 amp fuse for the wipers. These are located under the hood in the fuse/relay box. The best way is to be careful and use a set of pliers. The reason you pull the blower relay is so that it is easier to pull the intermittent relay. Clean these off the blades of the relay with a burnishing tool (in a pinch you can use your wife's nail polisher that is like very fine sandpaper. Once the are a pretty silver color, wipe them off with some rubbing alcohol. Put them in and pull them out about 5 times into the relay socket and leave them in. Clean the blades for the fuse with a cue tip and rubbing alcohol and then put the fuse in and pull it out about 5 times then leave it in. Hook up the negative terminal and take the key to the on position and turn the wiper to the lowest position. If it works if should take about 36 seconds between strokes. 2. The next easiest is taking the cover off the top of the steering column and pulling off the wiper switch and replacing it. There are three screws that hold the cover and two that hold the switch plus the electrical connector. You can buy a used one at a "junk yard" for about $20. 3. Replace the wiper motor (takes about a couple of hours start to finish). It involves removing the wipers, the cowl (plastic cover over the wiper motor right below the windshield), loosening and lifting the scissor arms for the wiper arms and removing the motor (this involves disconnecting the power connector and feeding it back to the motor).Hopefully your issue is like 95% of the wiper issues and it is just a little bit of corrosion on the wiper relays and fuse!

there are grounds that join behind batter remove battery check for corossion clean up and rejoin splice should work again

i belive that your wiper switch has gone out on the intermittent side. this is a very common problem.
I hope this helps you
Thanks
Please leave rating

my 2004 expedition had same problem, if you take apart the shaft that goes thru the glass it will be full of dirt, clean ,lubricate and reinstall, you may have to replace the O-ring on the shaft. a 20 minute job, very easy fix