2002 Nissan Maxima Logo

Related Topics:

A
Anonymous Posted on Jul 14, 2014

2002 nissan maxina po-335

Fuel pump working but no fuel to injector

1 Answer

Stephen

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Nissan Master 21,873 Answers
  • Posted on Jul 14, 2014
 Stephen
Nissan Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Jun 22, 2012
Answers
21873
Questions
0
Helped
6198675
Points
67230

Well code 335 is a problem with the crank sensor circuit.
The sensor would need to be tested.

5 Related Answers

Anonymous

  • 30 Answers
  • Posted on Dec 02, 2009

SOURCE: not running, just instaled new diesel pump

Bleed all the air out of the injector pipes. The car won't run with air in the system.

Ad

Anonymous

  • 4 Answers
  • Posted on Oct 14, 2008

SOURCE: MY 01 Nissan Altima does not want to start.

Sounds like either the fuel pressure regulator or a clogged fuel filter.

hiseyj

Jackson Hisey

  • 99 Answers
  • Posted on Nov 26, 2008

SOURCE: i have a 1999 nissan maxima with code P1320

This code is a crapshoot. There are two main things it could be and they are both expensive. There could be wire breakage in the engine harness. There is a thick harness coming out of engine bulkhead on the passenger/right side and it has a slight bend to it. With the engine idling grab that bend and give it a couple of twists and yanks. If the engine stumbles or misses that is the source of your troubles. If not, you more than likely need to replace the coils. Any one of the six coils could be causing the code so I recommend replacing all six at the same time. You could buy one coil for the front bank and one for the rear and swap it between cylinders to see which coil is causing the code. This is time consuming but cheaper.

Anonymous

  • 1 Answer
  • Posted on May 09, 2010

SOURCE: I have a 84' nissan diesel pickup with the sd25

loosen the nuts holding the fuel lines to the injectors, roll engine over and once fuel comes out, retighten nuts until all are tight again. After that, look at the stop solnoid as it will cut the fuel flow also

Anonymous

  • 3 Answers
  • Posted on Dec 28, 2011

SOURCE: 1998 Nissan Versa Vanette Cargo 2.3 Diesel, Timing mark position at TDC (1) for mechanical fuel injector pump. (old head cracked new head is being fitted)

thew timing marks for vanette cargo are on the timing belt u carnt go wrong

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

2002 Nissan Xterra 240,000 miles, cranks and runs but when shifted into gear dies.

check the fuel pressure and flow , if the pressure is low replace the pump, if the flow is low replace the fuel filter,the injectors may need some attention at that mileage.
0helpful
1answer

Not firing, changed fuel filter and crankshaft position sensor

Is the code still active, and are the injectors opening ?
Will it start using starting fluid ?
0helpful
1answer

I have a nissan maxina 1996. When I press the gas, the car doesn't respond. Smells a lot of gas. I changed all the sensors including the Mass air flow sensor and the whole throttle body with the sensor....

Considering the age of the car it would be wise to remove the fuel injectors and have them tested and have the fuel system checked for pressure and delivery volume, pressure regulator function...
0helpful
1answer

What's code po 335 on a 2006 nissan 350z

Code 335 is for a problem with the crank sensor. It could be a faulty sensor, the object the sensor reads, or the wiring from the sensor back to the computer.
1helpful
1answer

What codes is po345? ho do i fix it?

are you sure its po-345 because it dont show that code if it po-335 its crankshaft position sensor maybe re check code.what model is it ????
1helpful
3answers

I fixed used injection pump to engine and is not starting,i check oniy to fine out that the pump is not injecting fuel to the injectors.the timing is good.it is nissan navara 2000 model

1) There could be an air lock to the fuel system, try to bleed the system.
2) If the fuel is reaching the injector pump & not supplying to the injectors nozzles thn the pump needs attention.
Hope this helps!
0helpful
1answer

Not running, just instaled new diesel pump

Bleed all the air out of the injector pipes. The car won't run with air in the system.
0helpful
1answer

Po 307 misfire on #7

just because injector test ok electricly that doesnt mean its working right if the tip is plugged instead of sprayying a fine ignitable mist of gas it just drips out if this happens the gas wont ignite and you get a wet plug. you can switch injectors from one cylinder to anther or you can just replace #7 let me know how you make out with this
0helpful
1answer

Po 252

hi changing glow plugs is nothing to do with this code i would change the fuel filter and put a injector cleaner into the fuel tank as if this doesn,t cure the problem the only other thing that affects the pump is the timming belt has it slipped a tooth is there a marked drop in preformance if not these pumps are expensive very expensive best of luck yates210456
Not finding what you are looking for?

73 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...