Question about 1999 Jaguar XK8

Open Question

Parking brake light stays on and parking brake inop

Posted by Anonymous on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers breaklight not working replaced breaklight switch now wont' get out of park


The brake light switch controls all the brake lights. It will not correct a problem with only one light inoperative. One light out only may be a bulb/socket or power/ground to it. Not coming out of park ( Year/make/model didn't post ) is usually controlled by the brake light switch. Sounds as if the switch is not adjusted properly. MAke sure the brake lights come on when pedal is pushed

Feb 04, 2016 | Cars & Trucks

1 Answer

Why does the parking brake light stay on in my 2006 mira i alrady checked the brake fluid and hand brake system but problem is stil there kindly advice


Parking Brake Warning Light - RepairPal

repairpal.com/parking-brake-warning-light
  • As long as there are no problems detected in the parking brake system, the parking brake light will stay on until the parking brake is completely released.

Oct 08, 2015 | Cars & Trucks

1 Answer

WHY PARKING BREAK DEFAULT LIGHT 2004 XJ8 ?


if the park brake warning is on and the park brake is inop. there are several common problems with this system, the most likely causes are 1 the rear brake caliper sliders are part siezed or the pads siezed in the caliper frame 2 the wiring to the park brake motor open circuit or rubbed through on the rear subframe.3 the park brake motor has failed, you really needto get the fault codes out of the park brake module if the above checks out ok the above faults i have found to be the cause 9 out of 10 times. hope this helps.

Aug 09, 2014 | 2004 Jaguar XJ

2 Answers

Parking brake light stays on and parking brake inop


light instead of buying a switch near the believer rooms brakes don't work it's probably the cable

Jul 13, 2014 | 1999 Jaguar XK8

1 Answer

Inoperative brake and tail lights


hiya
cars dont have relays for brake lights as its too low power.
If you have power across the switch you may want to check the connections to the bulb holders and then check the bulbs themselves.
If no power at bulb holders you need to check the loom which, unless you have had some welding or similar disruption would be very odd.
Check for a good earth at rear bulb holders too, quite oftena poor earth will cause many faults.

Feb 03, 2018 | Ford Focus Cars & Trucks

1 Answer

1996 mercury sable starts after being charged but next day is dead again


there is a Safety Recall Notice
01S08Grease used on the adjustable pedal assembly may enter the brake lamp switch and contaminate the contacts. This may cause one or more of the following symptoms to occur:
-Brake lights stay illuminated or are inoperative.
-Shift Interlock disabled (will be able to shift out of "Park" position without depressing the brakes.
-Speed Control will not activate.
-Cannot shift the vehicle out of "Park."
-ABS Warning light illuminates on vehicles with ABS
-Battery Discharged."

Jun 11, 2012 | 2003 Mercury Sable

1 Answer

Can't shift out of park


This might work for you guy's replace the brake light switch
Easy step by step tutorial watch the video. im sure it will help.
MERCURY MARQUIS STUCK IN PARK
http://youtu.be/fgUn1TuHu-0

Dec 24, 2011 | 2000 Lincoln Town Car

1 Answer

Tail lights inoperatrive


Could be one of three things;
1. Check the fuses in the fuse box.
2. If all fuses are OK, check the headlight switch.
3. If this car has 'delay turn off lights' feature, the lighting control module should be checked.

Nov 12, 2011 | 1993 Lincoln Town Car

1 Answer

GMC 07 Serria backup sensor will not work. I had a new bumper installed. At first it beeper all the time. Now it will not come on. The DIC shows park assist off.


#PIT4878: Service Park Assist Message / LEDs Stay On Or Inop - keywords B0968 inoperative lamp led light lit module reverse urpa - (Jun 12, 2009) 999999995.gif Subject: Service Park Assist Message/ LED's Stay On or Inop Models: 2007-2009 Chevrolet Silverado 2007-2009 GMC Sierra With RPO UD7

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern: Some customers my comment of a Service Park Assist Message on the DIC and/or the LED indicators at the right rear pillar staying on or inoperative. This concern could be caused by the wiring harness to the LED indicators being pinched under a ground eyelet at the right rear pillar, as shown below.

2290161.gif
other issues could be the problem such as poor connections at each sensor or damaged sensors. to clear URPA codes,place ignition in run,(engine OFF),shift into reverse and turn key OFF.place shift lever into park and retest operation of URPA. if still inop URPA code(s) need to be retrieved before further diagnosis can be accurately done.

Sep 15, 2011 | 2007 GMC Sierra 1500

1 Answer

Unable to shift out of park upon starting. Pressing on brake petal upon shifting. Also noticing my brake lights are not coming on during this procedure. Owners manual mentioned about the gearshift anti...


Sounds like since the park lock and the brake lights are both inoperative, the faulty component would be the brake light switch which should be just above the brake pedal under the dash.

More info, let me know.

Charlie

Mar 12, 2011 | 1998 Ford Windstar

Not finding what you are looking for?
1999 Jaguar XK8 Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...