Question about 1995 Isuzu Rodeo

Open Question

How to fix Isuzu wizard remote control fault - 1995 Isuzu Rodeo

Posted by Anonymous on

Ad

1 Related Answer

Anonymous

  • 20 Answers

SOURCE: abs light on dash have checked sensors with scope

check wire connections at brakes calipers for breaks.

Posted on Jul 22, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Isuzu wizard 1999 3ltr disel was running mint after driving 4 k it just dies and won't stark again until it cools down this keeps happening. Any ideas on what could bee the problem. Thanks


run the fault codes
one indication is that the EVAP system is not venting the diesel tank and there is a vacuum problem not allowing the fuel to the pump

Jul 21, 2018 | Isuzu Cars & Trucks

1 Answer

Instructions to get fault codes from a isuzu wizard. What wires to bridge cheers


what year car,. 1989?
model is this a wizard model?
what country, you do know the PCM vary by year,country and engine
right?
see this page
see the vast confusing on what car?
http://en.wikipedia.org/wiki/Isuzu_MU

shocking this my be, but is reality, and fixya is a calif,. forum.
so not stating country, most here might think its a usa car, and is not.
ours is a 1989 under the Isuzu Amigo name

the questions are :
is it obd1, obd2, eobd or jobd, ECU comms.
if old like 1980 it has DLC. (to jump)
the DLC pins vary by, country and engine and year.
and by smog laws world wide.


Jan 24, 2015 | Isuzu Cars & Trucks

1 Answer

Instructions to get fault codes from a isuzu wizard


nice double post, back up one and read,
again, no year, no country or engine options stated
making any answers (correct) impossible.
for us to be wizards of wizards,we need input facts, correct. lOL

Jan 24, 2015 | Isuzu Cars & Trucks

1 Answer

How do i get flash fault codes off a 2000 isuzu wizard diesel, What terminals do i bridge??


data codes can be displayed by using a scan tool connected to to the data link connector located under the dash in the area of the steering wheel. It is a 16 pin connector.. This covers all isuzu vehicles from 1996 to 2007

Jan 24, 2015 | Isuzu Cars & Trucks

1 Answer

I have an isuzu wizard 3000cc 1998. i have just done the motor up. and it dose not want to run have done every thing to try get it going but so far its hard starting will not rev higher then 1.5 rpm a


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems ca cause many drive-ability related problem such as rough idle and other symptoms


Oct 18, 2012 | Isuzu Cars & Trucks

1 Answer

H0w do i fix p0601 on a 2006 isuzu ascender


well i can tell you what it is ,
(internal controler failure)
internal control module fault condition (check s u m )detectede
hope this helps

Sep 29, 2012 | 2006 Isuzu Ascender

1 Answer

I have a 1999 isuzu hombre truck gauges quit workong


My Isuzu Wizard lost all its indicators and hazard lights fuses all checked out good Problem found to be someone in the past replaced a fuse with a higher amperage fuse trailer fault blew the relays instead of just the fuses

Aug 13, 2012 | Isuzu Cars & Trucks

1 Answer

Hello. I have Isuzu Rodeo 2004. The OBD2 test shows failure of the P0602 I want to know what the problem says. ? Is there a way to fix the problem without replacing the part? Also I do not feel any car...


That's an ECM fault code. If you feel it's an error, easy way to confirm.
Take it to your local Autozone, Advance, etc autoparts store and have them do a FREE fault scan. They come out to your car, scan the faults, then reset your lights. Get the list from them and if ECM error comes up again then you know it actually has an issue.

Jan 04, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Does the 2002 wizard live have a diesel option.


my diesel isuzu wizard is shaking when i start it till i drife it above 40km/u

Apr 10, 2009 | 2002 Isuzu Trooper

Not finding what you are looking for?
1995 Isuzu Rodeo Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...