Question about 2007 Proton Satria Neo

Open Question

How do I disable the engine immobilizer in my Proton Jumbuck Ute, Build Date Oct 2007?

The key fob fell apart while I was part way through turning the key. Sounds a bit like unplugging your computer during a BIOS update. Anyway, the alarm and door locks are still working if I could just disconnect the immobilizer, I would be more then happy, or does it have to be, ("re-mobilized") first. If "re-mobilized" isn't a real word please don't bother telling me so!

Posted by David Hill on

Ad

1 Related Answer

emissionwiz

Marvin

  • 85239 Answers

SOURCE: how do i reset my key fob for a proton satria neo

Duplicate question.

Posted on Sep 28, 2012


Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to restart a proton jumbuck after a battery change


use a scan tool to reset the ECM and immobilizer

Jul 27, 2018 | Proton Cars & Trucks

1 Answer

Having trouble with my Proton Jumbuck ute. The battery has a drain of 0.10A. I have isolated the room light and clock the drain is still 0.10A. Are there any other circuits that come off this fuse?


0.10 amps is only 100 milliamps, and that is not enough to drain a battery. In fact, if your Ute has an engine computer, that may account for the amp draw. I'm not familiar with this car, as it is not sold in the US as that name. On some US cars, that circuit would be known as IOD (ignition off draw), and specifically for clock, radio pre sets, computer memory, and security parts if used. It is said as long as the amp draw is less than 150 milliamps (0.150A), everything is fine.
So, probably the engine computer, or radio pre-sets, or security apparatus, hey?

Jan 01, 2017 | Proton Cars & Trucks

1 Answer

I own a 2003 proton jumbuck ute and want to replace drive shafts, the outer wheel end not a problem but need to know what I have to do to release drive shafts from gearbox end. thank you for your time


most cv axles or held in the gear box /diff by a round sectioned circlip at the end of the splines in the diff
once you have the axle free of the hub and bearings use a heavy hammer on the back side of the cv joint or a heavy slide hammer attached to the end of the axle
you have to compress that circlip so that it allows the axles to slide out

May 30, 2016 | 2003 Proton Juara

1 Answer

Turn off engine light on proton jumbuck


fix the fault and use a scanner to reset the system

Feb 27, 2015 | Proton Cars & Trucks

1 Answer

My Toyota Yaris refuses to start after the key fob fell apart whilst starting yesterday. It is as though the immobiliser is on partially or fully. The electrics are fine and the started motor seems


Most likely there could be three reasons for your problem:
1. Gear selector switch on the transmission has poor connections at P and N. (Adjust or replace the selector switch assembly, if it is automatic transmission).
2. Starter motor assembly needs overhauling/ repair.
3. Harness wiring.
Even though if the immobilizer system is armed, the starter should run normally but the car would't start.

Oct 01, 2014 | 2001 Toyota Yaris

1 Answer

Inertia switch


Inertia switch is only relevant when you have a collision and the engien does not start. Fuel pump may not run and coils no spark. If not, same thing could also happen if the immobilizer is not disabled or the key FOB gets damaged. The ignition key has an RFID chip in it and if you drop your key or remove this chip, the car will not recognize the key and wont start. You need to use your spare key from then on.

Apr 15, 2014 | 2004 Proton Gen-2

1 Answer

I have a proton gen2 and the immobilzer has immobilized the car. When I put the key in to turn engine on nothing happens


Get your spare key and use it to start. If it starts, the key that cannot be used for starting has to replaced/reprogrammed. Don't forget to come back and rate my post.

Mar 07, 2014 | Proton Cars & Trucks

1 Answer

Ford focus 2001 1.4cl key fob not working


Is it your original key fob or a new one?

Jun 26, 2013 | Cars & Trucks

1 Answer

FIRING ORDER PROTON JUMBUCK


If it's 4 cylinders, it's 1-3-4-2. for Mitsubishi/Proton engines.

Jun 22, 2013 | Proton Cars & Trucks

Not finding what you are looking for?
2007 Proton Satria Neo Logo

Related Topics:

1,343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proton Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

gbob59

Level 3 Expert

3063 Answers

john h

Level 3 Expert

23515 Answers

Are you a Proton Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...