Question about 1995 Jeep Grand Cherokee

Open Question

How can i make a 98 grand cherokee 4.0l 4wd work in a 1996 grand cherokee 4.0l 4wd?

Posted by Joe Reynolds on

Ad

5 Related Answers

Anonymous

  • 30 Answers

SOURCE: 1996 Jeep Grand Cherokee wiper arm

The little blade lock will lift up. see image..."http://econtent.autozone.com:24991/znetrgs/repair_guide_content/en_us/images//0900c152/80/0a/9d/4c//medium/0900c152800a9d4c.gif"

Posted on Sep 30, 2008

Ad

Anonymous

  • 55 Answers

SOURCE: serpintine belt

This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.

http://autorepair.about.com/library/illustrations/bl506a-lib.htm

Posted on Jan 10, 2009

Ad

Efstathios Govas

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: 1996 Jeep Grand Cherokee window relay

Check in the Fuse Block, the cavity 2, fuse 30 Amp c/Brkr (Section (8W Page 7)

More details about electrical system for ZJ Grand Cherokee, you can find here: ZJ-Secc-8W-Wiring-Diagrams

I hope help you with this (rated this help). Good luck.

Posted on Sep 24, 2009

Ronnie Wilson

  • 1596 Answers

SOURCE: how do i replace the heater core on a 1996 Grand

REMOVAL AND INSTALLATION

Note:
This revised Heater A/C Housing service procedure is referenced from Technical Service Bulletin No: 24-02-98. Removal

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Sep 30, 2009

Testimonial: "Excellent!!! Thank you very much."

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to switch 4 wheel drive back to 2 wheel drive in my 98 Jeep Grand Cherokee


that is because you have Part time 4wd? (what do you have)?
and must not drive on pavement free of ice.
its now winding up the drive train, bad for it too.

drive, to dirt, sand, gavel or grass and shift out of 4wd.
or jack up 1 tire, and same,
one tire must be on slippery surface. at least.

http://www.rubicon-trail.com/4WD101/driveline-bind.html

this happens on all PT 4wd
or using LOCK on AWD. dont.

Mar 10, 2015 | 1998 Jeep Grand Cherokee

1 Answer

What type radiator clip or slot fits 1996 jeep grand cherokee v8 4wd


a jeep and a ram truck around the same year should be close.

Jan 24, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Where is the flasher located


1996 Jeep Grand Cherokee 4WD 4.0L MFI 6cyl:
The Flasher is located front seating area, driver side, under dash, driver side of steering column, mounted in convenience center.
Application:
- Hazard flasher
- Turn signal

Check the ZJ-Secc-8W-Wiring-Diagrams (page 8) for Convince Center graphics.

I really hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1996 Jeep Grand Cherokee

1 Answer

98 Jeep Grand Cherokee Power Door Lock Problem


I have a 1996 Grand Cherokee - the same problem, except my interior lights flash on and off at the same time. Did you get your problem solved?

Dec 21, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Crankshaft sensor located 98 jeep grnd cher 4wd 6cy


it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Sep 23, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Broken front coil spring


There were a lot of differences between a 98 TJ (Wrangler) and a 95 ZJ (Grand Cherokee). The grand cherokee is much heavier. Now might be the time for those "Off Road" upgrades you've been waiting on. And it is a good excuse.
Have a nice day!

Mar 25, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Serpintine belt


This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.

http://autorepair.about.com/library/illustrations/bl506a-lib.htm

Jan 10, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...