Question about 2003 Porsche Boxster

Open Question

How to install timing belt on 2003 camshaft

How to install timing belt on 2003 boxster on intermediate chain

Posted by Anonymous on

Ad

1 Related Answer

Patrick Rayome

  • 1757 Answers

SOURCE: I am looking for the serpentine belt diagram for a Boxster S

My sincere apologies for the delayed response.
I am personally going back to answer - unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagram you will need. It is located all the way down on the bottom of the page - so scroll all the way down!


If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/2003/make/porsche/model/boxster/2003_porsche_boxster_drive_belt_routing_diagram.htm

Posted on Mar 05, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set camshafts on 1999 duvil northstar


Remove camshaft covrs
Remove front cover
Remove or fully retract all three timing chain tensioners
Remove oil pump
Primary and secondary chain guides should remain in place. Rotate crankshaft until sprocket drive key is at about 1 o'clock position.
Set crankshaft and intermediate shaft sprockets into primary drive chain with their timing marks asjacent to each other.
Install crankshaft and intermediate sprockets over their respective shafts. Rotating crankshaft as necessary to engage crankshaft key in sprocket without changing the timing mark relationship.
Install Flywheel Holder Tool (J-39411) to lock crankshaft in position. Install intermediate shaft sprocket retaining bolt and torque to specifications.
Route secondary chain for left cylinder head over inner row of intermediate shaft teeth.
Route secondary drive chain over chain guide, and install exhaust cam sprocket to chain so camshaft drive pin engages the sprocket notch marked "LE" (Left Exhaust).
There dhould be no slack in the lower section of the chain, and the camshaft drive pin must be perpendicular (90 degrees) to the cylinder head surface.
Install the intake camshaft sprocket into the chain so the sprocket notch marked "LI" (Left Intake) engages camshaft drive pin, while drive pin remains perpendicular to the head face. Minor adjustments can be made to camshaft position to get pin to engage by using a wrench on the hex cast into the camshaft.
Install sprocket retainer bolts and torque to specification.
Repet steps as above to install the right secondary chain to the right camshafts. The right camshaft sprockets are marked "RE" and "RI". In addition, the RE sprocket must contain the camshaft position sensor pickup.

May 27, 2012 | 2000 Cadillac DeVille

2 Answers

Does 2003 Chevy ecotech motor have a timing belt or chain


It has a timing chain and a balance shaft chain also. My 2003 Cavalier jumped time about 2 months ago and that is what it had in it.

Jan 06, 2012 | 2003 Chevrolet Cavalier

1 Answer

How do i set the timing marks on a 3.4 liter engine


3.4L Engine Fig. 7: View of the timing chain and related components with the front cover removed — 3.4L engine 88003gb7.gif
Fig. 8: Retract the timing chain tensioner 88003gb8.gif
Fig. 9: The special tools must be used . . . 88003gb9.gif
Fig. 10: . . . to remove the timing chain, crankshaft sprocket and intermediate shaft sprocket 88003gc1.gif
Fig. 11: Slide the sprocket and chain on the shafts, maintaining the proper alignment 88003gc3.gif
Fig. 12: The crankshaft sprocket must be pressed on to specifications using a special tool 88003gc4.gif
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. For 1991 vehicles, perform the following:
    1. Remove the starter motor and flywheel cover.
    2. Remove oil pan retaining nuts and bolts. Remove lower frame and powertrain onto transmission table.
  4. Remove the front cover, as outlined earlier this section.
  5. Matchmark the intermediate sprocket, chain link, front face of cylinder and crank sprocket for reference.
  6. Retract the timing chain tensioner shoe by using J–33875 or equivalent, on both sides of the tensioner and pulling on the thru pin in the tensioner arm to retract the spring. While spring is retracted, insert a holding tool to hold it.
  7. Remove the timing chain tensioner retaining bolts.
  8. Raise and safely support the vehicle.
  9. Remove the timing chain, crankshaft sprocket and intermediate sprocket using tools J 8433 and J 28611, as shown in the accompanying figure. If the intermediate gear does not slide off easily with the timing chain assembly, rotate the crankshaft back and forth to loosen the tight fit.
  10. If necessary, remove the timing chain tensioner. To install:
  11. Check to ensure that crankshaft key is installed and fully seated and the chain tensioner is fully installed and blade retracted.
  12. Slip both sprockets and chain over the proper shaft and engage the slot in the key. The intermediate shaft may move against the rear cover. Slide the sprocket and chain on the shafts, maintaining the proper alignment shown in the accompanying figure. While installing note the following:
    1. Make sure the rubber and tension blade of the tensioner does not become caught, misaligned, or dislodged.
    2. The large chamfer and counterbore of the crankshaft sprocket are installed towards the crankshaft. The intermediate sprocket spline sockets are installed away from the case.
    3. The crankshaft sprocket must be pressed on for the final 0.31 in. (8mm) to the seated position using tool J38612 or equivalent, as shown in the accompanying figure.
    4. Check to make sure timing was maintained. Remove the retaining pin from tensioner.
  13. For 1991 vehicles, install the oil pan retaining nuts and bolts, and the flywheel cover and starter.
  14. Install the front cover, as outlined earlier in this section.
  15. Connect the negative battery cable. Start the engine and check for leaks.

Jul 09, 2010 | 1995 Chevrolet Monte Carlo

6 Answers

Does a 2003 320d e46 bmw have a timing chain or belt?


its got a timeing chain so dont try to change it

Nov 12, 2009 | 2003 BMW 325

1 Answer

How do you release the tension on the timing chains for the camshafts. i'm changing the head gaskets and can't figure out the timing chains tensioner. please help.


there are two large bolts in timing casing area 32mm size, one tensions cam chain the other tensions intermediate shaft chain, make sure engine is pinned in crank pulley to lock engine before releasing tensioners

Nov 04, 2009 | 2001 Porsche Boxster

2 Answers

Does my 2003 crv have a timing chain or a timing belt ?


It will have both. The timing belt is the rubber belt that you can see connected to all the pulleys. The timing chain is usually covered up and is located on the opposite side of the engine from the timing belt

Sep 30, 2009 | 2003 Honda CR-V

1 Answer

I am looking for the serpentine belt diagram for a Boxster S


My sincere apologies for the delayed response.
I am personally going back to answer - unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagram you will need. It is located all the way down on the bottom of the page - so scroll all the way down!


If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/2003/make/porsche/model/boxster/2003_porsche_boxster_drive_belt_routing_diagram.htm

Aug 04, 2009 | 1997 Porsche Boxster

2 Answers

What is recomended millage to replace 2003 Buick Regal timing belt?


a 2003 buick regal dosen't have a timing belt it has a timing chain

Jun 06, 2009 | 2003 Buick Regal

Not finding what you are looking for?
2003 Porsche Boxster Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14847 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...