How to fix 3rd tail light
SOURCE: 3rd brake light
This is how i did it on my 2006 Sonata
1.) unplug the connector in the trunk (its a small white plug running up to the third light, there should be a small clip you squeeze).
2.) remove the 2
gold-colored screws from inside the trunk. They can be seen from the
trunk. 1 is thru the larger square opening where the wire connects to
the 3rd brake light. The 2nd is on the right side thru a small
(screwdriver width) hole covered by a piece of foam tape stuff I had to punch me screwdriver through the foam to get to it.
3.) after removing the 2 screws, go inside the cabin and the brake light housing pops up.
4.) disconnect the bulb from the housing while inside the cabin (I had to do this with me two forefingers since the housing only pops up and inch or two).
5.) in the trunk remove the wire and bulb. (it's about 5 inches long. the wire from the connector to the bulb socket)
6.) reverse steps to install.
It is a pain and reqiuires a bit of time only because there isn't a lot of room to move around, but it beats taking it to the dealershio!
SOURCE: how do i change the front brake pads
First make sure you have the park brake on
Raise the front end make sure to support with jack stands
Remove tires
this should leave the front brakes exposed
there are two slide bolts holding the caliper in place loosen both and remove
then wedge a screw driver between the inner pad and the rotor and lightly pry towards you to take some pressure off of the caliper
you should now be able to lift off the caliper it will still have the brake line attached to it so be sure to secure it to something ie a bungie strap to the suspension or something do not just let it hang by the brake line
slide out the old pads out of the caliper mounting braket
now take a caliper press and push the piston back into the brake caliper use the old inner pad do not push directly on the caliper piston (if you dont have a caliper press just substitute a c clamp it works fine)
if replacing the rotors remove the caliper bracket once again two bolts
remove the caliper bracket
remove rotor
Make Sure to inspect the caliper for leaks or damage
To install reverse and youll be done before you know it
Make sure to lube slide pins with a small amount of brake grease and make sure the caliper moves freely apon installation
After you have done both sides
set down car and slowly pump the brake pedal about 15 times to close the distance between caliper piston and brake pads thats all
I hope this helps
SOURCE: timing belt on my 2002 hyundai accent 1.6 liter 4cyl
DID THE BELT BREAK AND THEN IT WAS CHANGED. If so then you may have bent valve. IF NOT then vehicle may be timed wrong. Here is a diagram of your timing marks, http://www.2carpros.com/car_repair_information/tec_info/2002/hyundai/accent/2002_hyundai_accent_timing_belt_diagram_marks.htm contact if you need more help. Thanks for using FIX YA
SOURCE: Broken Hyundai 2002 Accent door handles
i have a 2005 hyundai both back doors would not open from the outside . after taking the panel off i found out that the handle is completely plastic and that it had broke in half because off stress . i removed the handle ( which was a pain ) and used quick drying epoxy on the crack . then i put a thin piece if aluminum on each side of the crack and used the same epoxy to hold it on . the next day i put the handles back on ( after letting the epoxy dry ) and it has worked perfect ever since. my next recourse , if it breaks again , is go to ebay . there is a seller if you type in hyundai door handles that sells 2 after market ones for $39.99. they fit 2001 to 2005 . i hope that this helps .
SOURCE: In a 2000 Hyundai accent, clutch fluid = brake fluid
Yes that is correct. it should say what type right on the lid. example dot 3 or dot 4.
315 views
Usually answered in minutes!
×