Question about Daihatsu Rocky

Open Question

What is the cylinder layout for a Dodge 318 engine 1984 to set ignition timing

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 3 Answers

SOURCE: 1991 dodge ram 250 van 318 engine won't start

ALWAYS CHECK THE GROUND ON A DODGE

Posted on Nov 16, 2008


Richard Delahant

  • 1201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

Some dodges have an oblong shaped white ceramic block, either mounted on the firewall or on inner fender well, with wire connections, one on each end, if there is one, replace it.

Posted on Mar 16, 2009

Ad

Christopher Keene

  • 201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

Posted on May 09, 2009

motor1258

Mike Butler

  • 6674 Answers

SOURCE: wrong timing settings

10 degrees but not adjustable, computer adjusts as needed, unless it's a mile out. Did you have distributor out or something?

Posted on Jun 20, 2009

Noyb merlin

  • 38 Answers

SOURCE: misfire on #6 and #8 cylinder 1996 Dodge Ram 1500

Check the spark plug wiring . There are several places where the wires cross each other. These wire cross points MUST be at right angles to each other. Or you will have a misfiring problem.

Posted on Jul 07, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition lock removal no key 1984 dodge


as the key is required to remove you will have to pull the cylinder with a dent puller. The will brake the pin that holds it in .

Jan 05, 2015 | 1984 Dodge Diplomat

1 Answer

Where is the fuel filter located on a "1984" 318


1984 Dodge Truck Ramcharger 2WD 5.2L 2BL 8cyl

The Fuel Filter is located:Under hood, passenger side, upper engine area, mounted in fuel line

Jan 30, 2013 | Cars & Trucks

1 Answer

ADJUSTING VALVE CLEARANCE ON DODGE 318 ENGINE


There is no valve adjustment on that engine. Your rocker arms are on a single shaft that us bolted to the head. The lifters are hydraulic and will take up any normal slack unless there is damage to the cam, lifter, push rod or rocker.

Sep 10, 2011 | 1984 Dodge D150

2 Answers

Where is the ignition module located for a 1987 Dodge D-150 with a .318 motor?


It's in the engine compartment. On the drivers side firewall below the master cylinder next to the fender

Dec 26, 2010 | Dodge D150 Cars & Trucks

2 Answers

Does a 1984 dodge d150 regular cab 318 5.2 liter 2wd have catalic converter under the truck


It should , wether it still does or not after 26 years might be worth a look .. It will be in the exhaust system about 12-20 inches from the engine down pipe .

Jul 29, 2010 | 1984 Dodge D150

1 Answer

How do i set the correct timing for bmw 318 1992


ignition timing or valve timing
ignition timing can not be adjusted
and valve timing can only be set measured and checked with special BMW tool that locks onto the cylinder head

Jun 10, 2009 | 1996 BMW 318

1 Answer

Dodge 318 wiring diagrams


Why not eBay? you may be able to find a "lightly" used harness from an appropriate dodge or Chrysler product that uses your engines?
Try for a Repair manual or electrical repair segment for an appropriate Chrysler product with your engine.
http://www.manualslib.com/

May 01, 2009 | 1980 Chrysler Cordoba

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...