Can the evap system malfunctioning cause the engine to stop running?

PO128 -- engine coolant low or thermostat not working
P0440 - EVAP system malfunction, gas cap loose - Cat convertors missing from car can cause this
P1189 - Engine Oil Pressure Switch Circuit -- CAT CONVERTORS MISSING FROM CAR can cause this.

code po440 refers to evaporative emission (EVAP) system--malfunction ===causes --hose connections --intake leak--EVAP canister purge valve
code p0441 refers to EVAP system--incorrect flow detected===causes---hose connections --intake leak--EVAP canister purge valve.
once you fix the fault use a scanner to reset the engine light.

code p0440 refers to evaporative emission (EVAP) system--malfunction=== causes --hose connections --intake leak--EVAP canister purge valve
code po441 refers to EVAP --incorrect flow detected==causes the same as for po440
code po446 refers to EVAP system vent control --circuit malfunction===causes --wiring---EVAP can purge valve--ECM
generally I would replace the purge valve as it is common to all codes

code p0325 refers to knock sensor 1 bank 1 circuit malfunction===causes --Wiring---poor connection---Knock sensor.
code p0440 refers to evaporative emission (EVAP) system malfunction===causes--hose connection/s---intake leak---EVAP canister purge valve.

P0440 - Evaporative Emission Control System Malfunction
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0440 could mean one or more of the following has happened:
The gas cap is not installed or working properly
The purge solenoid has failed
The canister is plugged and not working properly

Possible Solutions: with a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

Check it and keep us updated.

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Causes: A code P0440 could mean one or more of the following has happened:
* The gas cap is not installed or working properly
* The purge solenoid has failed
* The canister is plugged and not working properly

Possible Solutions: With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
* Inspect the EVAP system for cuts/holes in tubes/hoses
* Inspect for damaged or disconnected hoses around the Evap purge solenoid
* Check and/or replace the sensor
* Check and/or replace the purge valve
* Have a professional use a smoke machine to detect leaks

Hope helps (remember to rate this).

16824/P0440/001088 - EVAP Emission Control Sys: Malfunction Possible Symptoms

• Malfunction Indicator Light (MIL) active

Possible Causes

• Evaporative Emission (EVAP) System leaking
• Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80) faulty
• Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115) faulty

Possible Solutions

• Check Evaporative Emission (EVAP) System Sealing
• Check Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80)
• Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115)

evap emission control system malfunction, po440

P0440 - Evaporative Emission (EVAP) System


evaporative emission (EVAP) system has a large leak.
Check the gas cap or vent valve. these are the most common problems.


The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the Fuel tank pressure sensor (FTP). When the sensor indicates a small leak in the EVAP system, this code is set.


Here are some additional causes.

* A small leak in any of the EVAP hoses or fuel tank hoses
* A small leak in the purge valve or vent valve
* The EVAP Canister may be leaking