Firing order diagram on a 2003 hyundai tiburon 2.7 eng.

some engines have no such thing
so is this a ,buddy told you change them out
or failed to look first as most have COP coils
look ma' no wires.

you mean firing order i bet.
best is remove and replace them 1 by 1, and not just yank them all off at once ever.
if did buy the service manual and read.
no engine told nor country told and all that varies by country.
Tiburon 2.7 Delta engine???? v6??>?
wiki facts we can not guess engines blind.
there are 3
in USA (are you) it is 2 engines, 2.0 and 2.7 v6

ok both engines full set of spark plug wires USA.
I have 1999 car with no wires , only COP coils.
rule #1 do not remove them all at once
or have to learn FIRING ORDER you must at the
spark end (cylinder #) and the distrib cap too
and rotor direction, al that, or fail it will
next time ask first/
>?
eg : 2.7L how to change spark wire set and not lose firing order. oops

How to change spark plugs hyundai accent 01 - 05 - YouTube

? 3:18
https://www.youtube.com/watch?v=tU2vwisJ7v4
Feb 16, 2012 - Uploaded by PNBNC
I filmed this right after changing my old plugs, I figured it was easy enough to film and some people can profit from it. for a ... Coil, you mean wire lol ... When you go to put the spark plug back in, never start it with the ratchet.

How To Replace Change Install Spark Plugs 2001-06 ...

? 3:17
https://www.youtube.com/watch?v=yVV2KcPDFIo
May 14, 2013 - Uploaded by 1A Auto Parts
... spark plugs. This video is applicable to the 2001, 2002, 2... ...spark plugs. This video is applicable to the 2001, 2002, 2003, 2004, 2005, 2006 Hyundai Elantra 2.0L. ... +queentonks A little know-how can go a long way. We're glad ... When do you think is good to replace my spark plugs wires? My spark ...
2001 Hyundai Accent Firing Order: Engine Mechanical ...www.2carpros.com/.../hyundai-accent-2001-hyundai-accent-firing-orderApr 23, 2009 - Engine Mechanical problem 2001 Hyundai Accent 4 cyl Two Wheel Drive Manual 95000 ... Now I'm trying to figure out how they go back on. How do I find out the Engine Firing Order for my car - Hyundai Accent 2001 1.5L?Which is cylinder 1 - 1.6 Accent - Hyundai Forum: Hyundai ...www.hyundaiperformance.com/.../16837-cylinder-1-1-6-accent.htmlJan 13, 2003 - 3 posts - ‎3 authorsFrom what I read though, the coil pack is configured as 1 4 2 3. I'm assuming the first wire on the coil pack goes to cylinder 1. Can anyone ...

A mechanic would check to see if the coil had voltage and a ground signal.

check if it has a crankshaft position sensor if it has test it-

Heres your diagram, good day and hope this is helpful.

For the 2000 Hyundai Tiburon 2.0L DOHC In-Line 4-Cylinder:

Firing Order:
1-3-4-2

Cylinders:
.........(back).........
|..1....2....3....4...|
.........(front)

Ignition Coil Connections:
(back)
...1
...4
...3
...2
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Sounds like he got some plug wires crossed in the process

If v6 may need to remove intake manifold and applicable parts to gain acess to spark plug coils, remove coils and remove plugs install reverse order
If 4 cyl remaove cover on valve cover remove spark plug coils etc.

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.

does your alarm system go off, and result in it not starting???