Need honda bmxa main valve body bolt torque specs

Here are some general torque specifications for the 1997 Ford Festiva's engine and suspension components. However, please note that these specs can vary based on the specific model and engine type. It's always best to refer to your vehicle's repair manual for precise information:

**Engine Torque Specs (in foot-pounds):**
- Cylinder Head Bolts: 35-50 ft-lbs
- Exhaust Manifold Bolts: 13-16 ft-lbs
- Intake Manifold Bolts: 18-24 ft-lbs
- Main Bearing Cap Bolts: 51-61 ft-lbs
- Rod Bearing Cap Bolts: 23-27 ft-lbs
- Flywheel Bolts (Manual Transmission): 58-73 ft-lbs
- Flywheel Bolts (Automatic Transmission): 61-76 ft-lbs

**Suspension Torque Specs (in foot-pounds):**
- Ball Joint Nut: 30-40 ft-lbs
- Control Arm Bolts: 60-80 ft-lbs
- Shock Absorber Upper Mount Nuts: 14-21 ft-lbs
- Shock Absorber Lower Mount Bolt: 40-55 ft-lbs

Remember that these values are approximate and can vary based on the specific model and any modifications made to the vehicle. Always refer to your vehicle's repair manual or consult a professional mechanic for accurate torque specifications to ensure proper installation and safety.

The torque specification for the cylinder valve cover stud/bolt on a 2007 Honda Accord 2.4L VTi is 7.2-8.1 lb-ft (10-11 Nm).
As for replacing the broken stud, it depends on how the broken stud is located and the extent of the damage. If the broken stud is easy to access, it may be a simple matter of unscrewing the old one and putting a new one in with the correct torque specification. However, if the broken stud is difficult to access or if it has caused damage to the threads, it may require a more complex repair. In some cases, it may be necessary to drill out the old stud and tap new threads or to use a helicoil insert to repair the damaged threads.
It's important to note that over-tightening the valve cover bolts/studs can lead to damage or deformation of the valve cover or gasket, and under-tightening can lead to oil leaks. So, it's crucial to torque the bolts/studs to the specified torque value.

Go on your computer in your browser and type in '1990 Honda Accord 2.2 4 cylinder head bolts torque specifications'. You will get back the engine bolt layout with the bolts numbered with the torque specs. You tighten the bolts according to the numbers of the bolts in the order starting with number 1 and working to the highest number.

I need all the specs of Isuzu npr 4hg1 engine.Cylinder head bolts torque, crankshaft bolts torque, connecting rod caps bolts torque
.

250nm

Torque specs on on 4L60 tranny pan in 04 escalade??

www.cadillacforums.com/.../cadillac-escalade.../260881-torque-specs-4l6...
May 26, 2012 - 3 posts - ‎3 authors Has 104000 miles on it now, figured it's time to change the filter and the fluid. ...Cadillac Escalade, EXT and ESV Forum - 1999 - 2006 Discussion, ... Flywheel toTorque Converter Bolt ... Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt ... Powered by vBulletin® Version 4.1.5 Re: SRX V8 Valve Cover Gasket Replacement Write Up ...
14 posts
Jun 10, 2015
2000 DTS Setting up Internal Mode Switch - 4T80E ...
9 posts
Aug 27, 2014
More results from www.cadillacforums.com

really on what part. or do you mean how much torque does it make

main caps 85 ftlbs (3divdedsetings30ftlbs all 50 ftlbs all ending at85ftlbs click, rocaps 45ftlbs, head bolts 85ftlbs workingfrom cdenter top ,center botom ,top center working clock wizeand out ,intake boltes45ftlbs again fromcenter working outleft side, right side,left, right 8 bolts one time only or u will distort gasket. oilpan from center alternate L side ,R side,clock wize25ftlbsclick recheck after breakin period valve covers 25ftlbs anrecheck flywheel 90ftlbs ,harmnic balancer bolt 75ftlbs, add oil!!!!run for 15 minutes drain oil &change filter run for 100miles for molly rings 10 mmiles for cast rings .let engine cool down retorque headbolts,replace valve covers .run it and get on it!!! good luck hve fun.

3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.