Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.
REMOVAL
Hope this helps and have an awesome day Roberta!
SOURCE: Remove inside panel pass.side door of 2001 Dodge gr.caravan sport
1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery
Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.
SOURCE: dodge caravan sliding doors
First, keep in mind that as you begin to remove these doors you run the risk of causing serious scratches to the paint and glass, so put some masking tape and/or plastic sheeting around both sides of the door (rear quarter panel and rear glass, front door and front door glass)
I would get a Haynes repair guide since that's what I have to work from and it will tell you step by step with pictures, what to do. It's not hard, but you need to get all of the attach points unhooked to be successful. Suggest you have a helper working with you to keep the door steady.
SOURCE: how to remove interior door panel on a 1997 caravan with ower windowq
Start by removing the negative battery cable from the battery. Then locate and remove the screws that hold the interior door handles in place (they may be hidden by snap in, or snap on covers). Once you have removed the interior door handles, disconnect the wire clips that go to your window and door lock controls.
I personally use a small pry bar to remove the interior door panel; it is held in by plastic snap clips. Try to get as close to, or directly under the snap clips as possible with your pry bar to prevent them from tearing out of the door panel. Once you have released the snap clips, pull the panel upward to remove it. Install in reverse.
I hope this information helps you, and I wish you luck on your repair.
SOURCE: 2005 dodge caravan engine light code p 441
If you mean code P0441 - This Relates to Incorrect Purge Flow for Evaporative Emission System
SOURCE: How to remove the inside door panel from a dodge
FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.
Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim
panel. Disengage wire connector from switch panel, if equipped Power
Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage
clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.
Hope helped with this; remember rated this help. Good luck.
379 views
Usually answered in minutes!
×