How can I replace the interior door handle in my susuki forensa 2006

https://www.google.com/#q=How+do+you+replace+the+driver+side+interior+door+handle+on+a+2006+Buick+rendezvous

YOU NEED A NEW INSIDE DOOR HANDLE,WILL HAVE TO TAKE COVER OFF TO DO.HERE'S ONE FOR YOU. For Ford Fusion Milan Zephyr MKZ IF29291 Front Left Inside Door Handle... HERE'S A LINK ON HOW TO REPLACE YOUR DOOR HANDLE. DIY How to replace your 2006 2012 Ford Fusion Interior Door Handle Group 1...

2006-2012 Hyundai Veracruz Inside Door Handle Genuine ...

? 0:45
www.youtube.com/watch?v=GQS89eacrOQ
Feb 10, 2015 - Uploaded by AutoPartsCheaper
Genuine OEM Hyundai front or rear interior door handle that fits the ... 2011 Hyundai Veracruz Limited Start Up, Engine, and In Depth Tour ...

1st you need to open door, remove plastic trim on inside of door by the handle, there is a hole where a 25 torx screw is holding handle end cap, pull door handle in open position, slacken screw until end cap is loose, remove end cap & slide door handle to rear of door out comes the handle, check with torch for any broken parts

Replacement door handles are found at a Dealer, and Salvage yard. Some auto parts stores stock a universal car/truck handle on their "Help Wall"...Your interior door panel usually needs to be removed to switch out the handle. Most are held in place with 10mm head bolts...(2) What kind of car?

plastic lock clip possibly broken . inexpensive part , just tricky to get into there .. , possibly just popped off ..

the arms have fallen on the lock latch inside the door. you have pull off door panel to fix it

This is a manufactures bulletin


SUBJECT:
Inoperative Right Front Door Switches OVERVIEW:
This bulletin involves replacing the right door interior handle. The loss of ALL functions may occur when attempting to control them from any of the switches located on the right door due to electrostatic discharge through the right door interior handle. The right door interior handle must be replaced to protect the switch module from static electricity. The new handle is more resistant to electrostatic discharge. MODELS:
2004 - 2008 (CS) Pacifica SYMPTOM/CONDITION:
The vehicle operator may experience a permanent loss in ability to actuate ALL of the following functions from the right door switches: ^ Power door locks. ^ Right power mirror. ^ Right power seat adjustments. ^ Right power window control. ^ Right heated mirrors. ^ Memory functions associated with the listed systems on right side (if applicable). ^ Loss of communication with the right door switch module to Scan Tool: DIAGNOSIS:
Perform a "Hard Reset of the right door switch module. This may be accomplished by removing all power (including memory keep alive power) from the right door switch module by unplugging the module power connector. Alternatively, vehicle power may be interrupted by removing the negative battery terminal when the ignition switch is in the OFF position. If after performing the hard reset functions of the right door switches return perform the Repair Procedure.


PARTS REQUIRED:
REPAIR PROCEDURE:
1. Disconnect the negative battery cable. 2. Remove the right door trim panel
3. Remove the door tweeter speaker. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Audio > Speaker > Removal (Fig 1). 4. Remove the power seat switch. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Power Seats > right Seat Switch > Removal. 5. Replace the right door interior handle, p/n 05170261AA, as described on Mopar Instruction Sheet K6855628 included in the handle kit. 6. Install the power seat switch. 7. Install the door tweeter speaker. 8. Install the right door trim panel. 9. Connect the negative battery cable.

They say it best here,I hope this helps. Tehy are replacing door handles, good luck.

http://dsvettes.com/new/pdf/DSV_passenger_door_handle_install.pdf

http://dsvettes.com/new/pdf/DSV_driver_door_handle_install.pdf

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the inner door handle and replace with new one. If it's your outer door handle, pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door