2008 Toyota Prius Logo

Related Topics:

A
Anonymous Posted on May 01, 2014

Stuck seatbelt prius

Front driver side seat belt will not latch. Help!

5 Related Answers

Anonymous

  • 1861 Answers
  • Posted on Sep 23, 2008

SOURCE: 2002 Toyota Solara Convertible seat belts not retracting

The front seatblet retractor springs have weakened. Unfortunatly, there are no "user serviceable parts" on them. They would have to be replaced. How many miles is on it? If you have low mileage, the Toyota Customer Experience Center may provide you some assistance, as the belt replacements are quite expensive. I'd call the CEC and explain your dilemma. Here is the number: 1-800-331-4331

Ad

Anonymous

  • 1861 Answers
  • Posted on Oct 07, 2008

SOURCE: replace rear seat belt in 1993 Toyota Corolla

OK. On the front edge of the seat bottom cushion, pull up hard, both sides. This will dislodge the 2 clamps that holds the seat cushion to the floor. Pull the seat cushion out & set it aside. You will now see the female latches bolted to the area where the rear of the seat cushion meets the rear seat back bottom. Remove the bolts (14 mm I think).

Anonymous

  • 1 Answer
  • Posted on Apr 07, 2009

SOURCE: Electric retractable seat belt problem

can you help with this problem

Anonymous

  • 1 Answer
  • Posted on Aug 17, 2009

SOURCE: my drivers side automatic seatbelt is stuck on the

Open small plastic access panel located between front and rear doors a few inches above floor. Disconnect the two wire connector (usually attached to car frame) and locate the male pin connector, usually 1 red and 1 blue wires. Run two long wires from a car battery neg. post and pos. post (battery on the car or separate.) Hold one wire against one pin of the connector and quickly touch the other wire against the remaining pin. This will cause the motor to turn in one direction. If motor turns in wrong direction simply reverse the wires until motor brings belt to desired position then quickly remove the wires. Reattach connectors to resume 'normal' operation after 'CAUSE' has been repaired.

Anonymous

  • 5 Answers
  • Posted on Nov 11, 2009

SOURCE: automatic seatbelts to manual seatbelts

if i were you i would try to make the ones from either the mark 3 supra or try the es250.. im trying to get it to work with the supra but i think your best bet is from the lexus es250. they share the same chassis obviously so most parts are interchangeable.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Driver seatbelt stuck

Try squirting some type of penetrating oil down where the belt inserts into the lock, then while pushing the release button as hard as you can, wiggle the belt latch up and down as hard as you can. Personally, I like SiliKroil penetrating fluid.
0helpful
1answer

How do i get my passenger side seatbelt unstuck? it is stuck around the front passenger side seat and i cannot undo it

move the seat back to release tension on the belt buckle and then undo it.
Does that help? If not reply.
4helpful
1answer

'06 Volvo V50 drivers seat belt is jammed, there is no play in the belt and the ratchet locks immediatly no matter how gently it's pulled. Same problem with passenger side the day before but it righted...

I solved this on my 95 volvo 850 glt as follows:

pull the seatbelt pilar cover off from the door jamb. this runs vertically up the pilar between the front an back door (beside the front seats. Once opened loosen the belt by gently pulling the belt upward toward the roof. You'll have to do this sometimes in small increments. Once the seatbelt is pulled out all the way, spray small amount of lubricant into the joint where at the top of the belt spool. Also use a screw driver to push spool upward while pulling the belt. At first it's only going to release a little but eventually the lubricant will work its way into the seam at the top of the belt spool and loosen up the stuck inertia catch. Until it completely loosens you might have to remove the pilar cover again and work the seatbelt out (also use the screw driver technique described above) in order to use the seatbelt. When parking, I would relatch the seatbelt and pull the slack up around the back of the head rest. After a day or so it worked normally.

good luck and don't give up.
4helpful
1answer

Hyundai getz seatbelt light is permanently on

the seatbelt light/warning illuminates only if driver has not buckled up also the belts are pretension if car has front impact along with air bags so may i suggest that you check under front seats that the wires for seatbelt actuation have not come loose ?either at plug or the belts lockup at side of seats check also for damp on carpets this too causes elec/s malfunctions
9helpful
3answers

Seat belt stuck on 1995 850 volvo

I solved this on my 95 volvo 850 glt as follows:

pull the seatbelt pilar cover off from the door jamb. this runs vertically up the pilar between the front an back door (beside the front seats. Once opened loosen the belt by gently pulling the belt upward toward the roof. You'll have to do this sometimes in small increments. Once the seatbelt is pulled out all the way, spray small amount of lubricant into the joint where at the top of the belt spool. Also use a screw driver to push spool upward while pulling the belt. At first it's only going to release a little but eventually the lubricant will work its way into the seam at the top of the belt spool and loosen up the stuck inertia catch. Until it completely loosens you might have to remove the pilar cover again and work the seatbelt out (also use the screw driver technique described above) in order to use the seatbelt. When parking, I would relatch the seatbelt and pull the slack up around the back of the head rest. After a day or so it worked normally.
3helpful
1answer

91 Camry Seat belt and power winodws on Passenger side Inop

More than likely, you have a broken wire or two between the body and the driver side front door. This is a very common issue with those cars when tey get older.
0helpful
1answer

Need to replace driver seat belt latch . Do you need to remove seat to get to seat belt bolt . It seems to be fastened to side of seat frame

yes, the seat has to come out , you may possibly hae to pull the seat frame apart. make sre the vehicle is not equiped with seatbelt pre-tensioner.
1helpful
1answer

Replace rear seat belt in 1993 Toyota Corolla

OK. On the front edge of the seat bottom cushion, pull up hard, both sides. This will dislodge the 2 clamps that holds the seat cushion to the floor. Pull the seat cushion out & set it aside. You will now see the female latches bolted to the area where the rear of the seat cushion meets the rear seat back bottom. Remove the bolts (14 mm I think).
Not finding what you are looking for?

77 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...