Question about 2007 GMC Yukon Denali

1 Answer

How do you remove interior door panel of 08 yukon denali if the door wont open

Posted by v mcginnis on


1 Answer

Dan Jacobs

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • GMC Master
  • 808 Answers

Remove seat and then it is still tough. to get the panel off.

Posted on May 01, 2014


5 Related Answers


  • 1 Answer

SOURCE: location of fuse box/panel for 2004 yukon denali xl

There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Posted on Oct 20, 2008



  • 85239 Answers

SOURCE: can't program my garage door opener

go to the link below (GM web site for owners) and then select your year and model, U will need a Yahoo mail account to sign in.

Posted on May 21, 2009


  • 1986 Answers

SOURCE: door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009


  • 1986 Answers

SOURCE: How do I remove the passenger side interior rear

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to everything.

Posted on Sep 18, 2009


  • 143 Answers

SOURCE: programming garage door openers for

Press and hold the two outer buttons on the homelink system in the car until the led flashes rapidly or goes out. Then hold the programmed remote up to the homelink system and at the same time press the button on the remote and the button on the homelink until the led light blinks rapidly or goes out. It should take less than 30 seconds. ----- Then go to the motor head and press the colored learn button on the motor head and go back to the home link and press the homelink button 3 times to activate. If your opener has dip switches stop at -----. Thanks BB

Posted on Sep 17, 2010

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Does the Bose system in a 2003 Yukon Denali have a fuse

yes open drivers side front door fuse access panel near door hinge side pull from bottom out look on back side of door for fuse location

If you need further help, I’m available over the phone at

Feb 27, 2015 | 2003 GMC Yukon Denali

2 Answers

How do I remove the inner door panel on a 2007 GMC Yukon XL Denali to get access to the door opening/lock rod system?

Welcome to Fixya

Disconnect the negative battery cable first to ensure your safety. You will see a small trim panel a few inches above the interior door handle (behind the armrest). Pry off the panel with the trim panel tool or a flat-head screwdriver. Remove the two 10 mm bolts that are behind the small trim panel. Pry off the vertical trim panel mounted on the handle that connects the power window controls and the door panel. Once the panel is removed, use the socket wrench to pull out the two bolts behind it. Pry off the small plastic piece around the door lock tab (upper part of door handle). Once the piece is removed, detach the door lock tab with your hand. Unfasten the sail panel using the trim panel tool or the flat-head screwdriver. The sail panel is on the corner of the door panel, directly across from the outside mirror. The panel is only attached by clips. Pull your interior door handle toward you, and pry off the trim panel behind it. Remove the bolt made visible with the panel removed. Pry up the power window control panel. Then unhook the electrical harness from the rear of the panel. Use the door trim tool to unhook the door panel clips. Insert the tool between the door panel and the door, and release the clips. There are several clips on each side of the door panel. Push the door panel up, then pull it away to remove it from the door.'

Thank you for using Fixya!

If you need further help, reach me via phone at

Aug 21, 2011 | 2007 GMC Yukon XL Denali

3 Answers

How do you replace an exterior door handle on a 2008 Yukon Denali

u can access thes handles by removing the door panel. u then unhook any cables and wires to the panel and then peel back the noise supressor film and then can u actually see the handles an bolts attaching the handle an a couple of linkage rods attach to it. kind of an easy job....good luck

May 10, 2011 | 2008 GMC Yukon

1 Answer

My out side door handle on the driver side came loose 2007 danali

It most likly broke inside. You will have to remove interior door panel to access all the bolts and rods to replace it.

Feb 10, 2010 | 2007 GMC Yukon XL Denali

1 Answer

The sound in the car completely stopped working in the middle of a movie...not even the blinker/turn signal makes a sound. What could have caused this, how do we fix it? We've checked the fuses and nothing...

I had this problem several months ago, but for some reason it started working again on its own. Haven't had the issue since (btw, this is on an '08 Yukon Denali XL). No sound, blinkers were silent, the headlights on warning when the key was out and driver's door opened didn't work. I did learn that the blinker clicking is generated in the audio system. It used to be a relay that clicked. Check for pinched wire harness below and around the drivers seat.

Nov 14, 2009 | 2007 GMC Yukon XL Denali

1 Answer

Passenger power window in my 2002 GMC denali keeps sliding down

well look for little pop outs first then then look for screws in those little openings then look on the outside edge of the trim panel for retainers to remove then pull the mirror cover off just pops of then pop out bottom of the door and then pop out the sides of the trim then pull up and out should come right off after that take vapor barrier off and then you will see the interior parts of the door and mechanics of the door/ Please rate my response thank you very much

Dec 29, 2008 | 2002 GMC Yukon Denali

2 Answers

The cargo door and glass is locked, and the actuator will not unlock.

how do you removed the interior cover? for the rear door actuator?

Oct 12, 2008 | 2006 GMC Yukon Xl Denali

1 Answer

How to replace exterior door mirror on 2003 Yukon XL?

First unscrew all the screw on the door then remove interior panels gently with screw driver and open the protective plastic film then remove all the wirings from the car and then remove the bolt from the car body and fit new door and make the wiring should be plug to car door as earlier...................

Jun 10, 2008 | 2003 GMC Yukon XL

Not finding what you are looking for?
2007 GMC Yukon Denali Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides