Question about 1984 Chevrolet El Camino

Open Question

How do i remove wheel cylinder on el camino - 1984 Chevrolet El Camino

Posted by Anonymous on

Ad

5 Related Answers

rick_amick

Rick Amick

  • 73 Answers

SOURCE: EGR Valve

remove the vacuum line and either 2 nuts or 2 bolts holding it to intake manifold. clean gasket material from mating surfaces and reinstall.

Posted on Mar 25, 2009

Ad

Anonymous

  • 51 Answers

SOURCE: rewiring 1959 chevy el camino

Are you needing advice, links, tricks, or all of the above?
If it's advice you want:
If you are not buying an after market harness and all of the oem wiring is intact replace one wire at a time from the component all the way back to the fuse box. Its tedious but, it's a sure fire way to get it right the first time.

Secondly, I'd by a haynes manual or some other wiring diagram. Study it for at least a couple weeks or until you are completely comfortable taking on the task.

Color code your wires and label both the old and new ones with paper tape and a permanent marker so that you know what each one is for.

Last but not least, make sure that the battery is disconnected... ;o)

Posted on Jun 01, 2009

Ad

Anonymous

  • 2317 Answers

SOURCE: lost my ignition key for a 76 el camino .... how

You'll need a steering wheel puller and a lock plate removal tool. Remove the steering wheel and the lock plate. There should be a button to push or screw to remove to take out the cylinder.

Posted on Mar 06, 2010

madhillbilly

  • 100 Answers

SOURCE: 1985 el camino distibutor spark plug diagram

the library has books you can look at (haynes, and chilton manuals) or if you want to buy a book you can go to the auto parts store and buy one. they will have the information you are seeking

Posted on Mar 22, 2010

ftw1952

frank thomas wilson

  • 10319 Answers

SOURCE: how do you remove, then

use snap ring pliers found at NAPA auto parts stores

Posted on Sep 08, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the turn signal flasher located in an 87 El Camino?


Under the dash on the left side of the steering wheel. You'll see the fuse panel. There is a flasher on the front side that you'll see and one one the backside. They are both the same. On is for the turn signal, one for the flasher.

Oct 13, 2014 | 1987 Chevrolet El Camino

1 Answer

How to remove ignition switch from 1977 chev el camini tilt column


Pull the steering wheel, get the push down tool to push down the lock plate to remove the plate, then pull the turn signal cam theres a screw on the right hand side of the shaft that holds the cylinder in.

Jul 23, 2010 | 1982 Chevrolet El Camino

1 Answer

How do I get the old iginition key lock out of the


There should be a button inside the column that you push in, or a bolt to remove, been awhile since I did one. You may need to have the key in the lock cylinder and turn the lock cylinder.

Apr 23, 2010 | 1982 Chevrolet El Camino

1 Answer

Lost my ignition key for a 76 el camino .... how do iremove the cylinder to replace it


You'll need a steering wheel puller and a lock plate removal tool. Remove the steering wheel and the lock plate. There should be a button to push or screw to remove to take out the cylinder.

Mar 06, 2010 | Chevrolet El Camino Cars & Trucks

1 Answer

1980 el camino fuse location


under the dash to the left of the steering wheel. U may have to remove the trim under the dash to see it.

Feb 18, 2010 | 1982 Chevrolet El Camino

1 Answer

Horn wiring diagram 65 el camino


a 1965 camino,centre steering wheel horn push? remove the steering wheel and check the carbon brush that runs against the copper metal ring on the bottom of the steering wheel

Dec 24, 2009 | 1982 Chevrolet El Camino

1 Answer

How to remove 82 chev el camino brake rotor


Remove the front wheel, use a flat head to take of the dust cap in the center of the rotor. There will be a big nut with a cotter pin going through it. Remove the pin and the take the nut off. After removing the caliper you will be able to remove the rotor and the bearings inside.

Oct 04, 2009 | 1982 Chevrolet El Camino

1 Answer

Ignition removal process for 1984 chevy 1/2 ton


This Outlines Removal Of Both LOCK CYLINDER<< Mechanical)) And The Ignition SWITCH ITSELF<< ELECTRICAL))
  1. Remove steering wheel as outlined previously.
  2. Remove turn signal switch as outlined in ``Turn Signal Switch, Replace'' procedure.
  3. Place ignition switch in ``Run'' position, then remove lock cylinder retaining screw and lock cylinder.
  4. To install, rotate lock cylinder to stop, while holding housing as shown, Fig. 6. Align cylinder key with keyway in housing, then push lock cylinder assembly into housing until fully seated.
  5. Install lock cylinder retaining screw. Torque screw to 40 inch lbs. for standard columns, or 22 inch lbs. for adjustable columns.
  6. Install buzzer switch, turn signal switch and steering wheel


CABALLERO, EL CAMINO, C, K, R, V & 1986---87 G MODELS
The ignition switch is mounted on top of the mast jacket inside the brake pedal support and is actuated by a rod and rack assembly.
  1. Disconnect battery ground cable.
  2. Disconnect and lower steering column. On some models, it may be necessary to remove the upper column mounting bracket if it hinders servicing of switch. Use extreme care when lowering steering column to prevent damage to column assembly. Only lower steering column a sufficient distance to perform ignition switch service.
  3. On Caballero and El Camino, rotate ignition lock to ``Off'' unlocked position.
  4. On C, K, R and V models, rotate ignition lock to ``Off'' locked position.
  5. If lock cylinder has been removed, pull switch actuator rod up to stop, then pushrod down to second (Caballero or El Camino) or first (C, K, R and V models) detent as shown, Fig. 7.
  6. Remove column mounted dimmer switch, if equipped, then remove switch retaining screws and switch.
  7. Reverse procedure to install, noting the following:
    1. Place gear shift lever in neutral.
    2. Place lock cylinder and switch in positions noted in steps 3 and 4.
    3. Fit actuator rod into hole in switch slider and secure switch with retaining screws, ensuring switch does not move out of detent.
    4. Install and adjust dimmer switch, if equipped, as outlined in ``Column Mounted Dimmer Switch, Replace'' procedure.
    5. Torque retaining screws to 35 inch lbs., then check switch operation.

Feb 21, 2009 | 1984 Chevrolet K1500

1 Answer

EGR Valve


remove the vacuum line and either 2 nuts or 2 bolts holding it to intake manifold. clean gasket material from mating surfaces and reinstall.

Jun 22, 2008 | 1984 Chevrolet El Camino

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

john h

Level 3 Expert

23504 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...