Question about 2001 Dodge Grand Caravan

1 Answer

Locate and replace check engine bulb

My check engine bulb is burned out. I replaced the bulbs in the instrument panel. But this did nothing for my check engine light. My owners manual showed the symbol but not where it was located. I need to find it and figure out how to replace it. Thanks

Posted by Joe Franklin on


1 Answer

David Cass

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 33 Answers

Probley have refer problem to dealer on this kind of thing or ask well known tech.

Posted on Apr 15, 2014


5 Related Answers


Ronald Mueller

  • 1263 Answers

SOURCE: tail light malfuction

check the brown wire on the tailight harness on the truck chances are it shorted and broke away from the assembly. the fuse is in the junction box under the hood.

Posted on Sep 02, 2008



  • 85239 Answers

SOURCE: changing instrument panel light bulbs

You have to remove the entire cluster assembly to get to the bulbs, there is no other way, no room for this man's hand at the back.

Posted on Nov 10, 2008


  • 30 Answers

SOURCE: Change the bulb in the courtesy reading lamp?

if this is the light you push up on to turn on and off you use a small screwdriver and pry it down. it is held by 2 plastic pins that snap into holes.

Posted on Jun 25, 2009


  • 109 Answers

SOURCE: Need to change lightbulbs on instrument panel

go to your local Chrysler dealer a buy the proper bulbs, they come complete and proper wattage, and they are cheap in price. word of caution replace all the illumination bulbs, when one is black the rest will follow. GOOD LUCK RDJRP

Posted on Aug 07, 2009


  • 83 Answers

SOURCE: Need to replace instrument cluster/AC bulbs

Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster

(5) Remove the instrument cluster from the instrument

Posted on Oct 02, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Check engine light doesn't come on

The bulb is burned out that illuminates the check engine light in the instrument panel. Replace bulb.

If you need further help, I’m available over the phone at

Oct 21, 2015 | 2002 Daewoo Nubira

1 Answer


All instrument panel lights or just speedometer light? There are several bulbs behind instrument panel. More than likely, the bulb at speedometer is burned out, and can be replaced by removing instrument panel and replacing bulb(s). Hope this helps.

Nov 12, 2013 | Cars & Trucks

1 Answer

Replace check engine light bulb

Take out instrument panel completely. Remove all bulbs and hold the panel up to the sun while looking at the back of it. You will see where each warning/info bulb goes.

Sep 26, 2013 | Chevrolet Aveo Cars & Trucks

1 Answer

Replace check engine light bulb

You will have to remove the instrument panel, but not the whole dash. See here, p111. Note you only have to do steps 9, 10, 14 to 16, 19 to 23. When you take out the instrument panel, you will see the light in its socket on the back. It is a wedge type globe, quite easily available.

Aug 28, 2013 | Toyota ECHO Cars & Trucks

1 Answer

Check engine bulb

I believe this are the ones on the instrumental panel, you would have to take the instrumental panel out and identify which one is 'burnt' and replace with a new one. I changed mine, bought the bulbs from a honda dealer. Good Luck

Jul 20, 2013 | 1998 Honda Accord

1 Answer

Rpm backlight out

You must remove the cluter of gauges and replace the light bulb.
    • 1Turn off the engine of the Taurus, and open the hood.
    • 2Remove the negative ("-") battery terminal from the battery in the engine compartment using a socket wrench.
    • 3.
      Insert a slotted screwdriver between the covers on the steering wheel column, and pry upwards. Pull off both the upper and the lower covers.
    • 4Position the steering wheel as low as it can go.
    • 5Remove the two screws above the Taurus' instrument panel and the four screws below it using a Phillips screwdriver.
    • 6Insert a slotted screwdriver into the dashboard trim, and pull upwards to pry it off the vehicle. Disengage the eight snap clips from the dashboard trim by hand, and pull it out of the vehicle.
    • 7Uninstall the two securing screws from the instrument panel with a Phillips screwdriver.
    • 8Pull the instrument panel towards you, and reach behind it to disconnect the two wiring plugs. Pull the instrument panel out of the Taurus.
    • 9Replace any burned-out bulbs from the underside of the instrument panel with new bulbs. Pull the old bulb off, and push the new bulb in.
    • 10Reassemble the instrument panel and dashboard trim in the reverse order of removal. Reconnect the battery, and close the hood.

Nov 06, 2012 | 2008 Ford Taurus X

1 Answer

How to change bulbs in instrument cluster. The left half of the instrument panel lights up. The right half (speedometer, oil pressure, fuel) does not. I assume a bulb has burned out. How do I change...

Take out the screws holding the instrument panel in, pull it gently away from the dash being careful not to unplug or pull out any wires. there should be a plastic retainer that you and pull off to get at the bulbs.replace the blown bulbs and reinstall the panel..

Jan 29, 2011 | 1995 Isuzu Rodeo

1 Answer

I have a 1993 Chevy Blazer S10 Tahoe and the speedometer light is out. I can see everything on the right side of my instrument panel at night, but nothing on the left. How do I change that bulb (or bulbs),...

You have to remove the instrument cluster to replace the bulbs [the bulbs go in from the backside] Not to difficult of a job but I would suggest replacing every bulb in the back while you have it out as they are all the same age and it seems that once one burns out the others aren't far behind. I don't know the bulb number but most parts stores or a GM dealer can figure out which ones you will need. The bulbs are held in by small plastic bulb holders that you push gently and turn to remove from the back of the cluster.

Jun 25, 2010 | 1997 Kia Sportage

1 Answer

How to change check engine bulb

You must remove the instrument panel to replace this bulb. You must first remove the bezel around the instrument panel to gain access to the screws holding the instrument panel in. Once the panel is removed it is just a matter of replacing the bulb in the back of the panel for the check engine lamp.

Nov 07, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2001 Dodge Grand Caravan Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides