Question about 2011 Suzuki Grand Vitara

Open Question

Engineering mode how to access engineering mode

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can you tell me the location of my neutral safety switch on my 2008 Ford F2 50 super duty super cab 5.4 L engine automatic transmission

It's not called neutral safety switch .
Transmission Range (TR) Position Sensor Assembly
The transmission range (TR) position sensor assembly is an internally mounted sensor that includes the detent spring, rooster comb and bracket, located next to the solenoid body. The components of the TR position sensor are factory adjusted to each other and the sensor must be installed as a calibrated assembly. The TR position sensor contains electronic circuitry that provides the PCM a fixed frequency at a duty cycle for each of the various positions of the manual lever (PARK, REVERSE, NEUTRAL, DRIVE, M3, M2 and M1) to the PCM. The PCM uses the TR position sensor signal for engine functions (start, reverse lamps) and for line pressure control, shift scheduling and TCC operation.

Your best bet , take your vehicle to a qualified repair shop or Dealer .

Diagnosing an electronically controlled automatic transmission is simplified by using the following procedures. One of the most important things to remember is that there is a definite procedure to follow. DO NOT TAKE SHORT CUTS OR ASSUME THAT CRITICAL CHECKS OR ADJUSTMENTS HAVE ALREADY BEEN MADE. Follow the procedures as written to avoid missing critical components or steps. By following the diagnostic sequence, the technician will be able to diagnose and repair the concern the first time.
On-Board Diagnostics with Scan Tool
NOTE: For detailed instruction and other diagnostic methods using the scan tool, refer to the tester manual and the Powertrain Control/Emissions Diagnosis (PC/ED) manual.
These quick tests should be used to diagnose the PCM and should be carried out in order.
  • Quick Test 1.0-Visual Inspection
  • Quick Test 2.0-Set Up
  • Quick Test 3.0-Key On, Engine Off
  • Quick Test 4.0-Continuous Memory
  • Quick Test 5.0-Key On, Engine Running
  • Special Test Mode
    • Wiggle Test
    • Output Test Mode
  • PCM Reset Mode
  • Clearing DTCs
  • OBD II Drive Cycle
  • For further information on other diagnostic testing features using the scan tool, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. Other diagnostic methods include the following.
    • Parameter Identification (PID) Access Mode
    • Freeze Frame Data Access Mode
    • Oxygen Sensor Monitor Mode
    • P0706 TR Sensor TR sensor frequency fault detected. TR sensor signal frequency is out of normal range. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. For gasoline engine vehicles, Go To Pinpoint Test C . For diesel engine vehicles, Go To Pinpoint Test H . P0707 TR Sensor TR sensor circuit duty cycle low input. TR sensor signal duty cycle is below threshold, sensor/circuit electrical malfunction. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. For gasoline engine vehicles, Go To Pinpoint Test C . For diesel engine vehicles, Go To Pinpoint Test H .

Jul 25, 2018 | Ford Cars & Trucks

1 Answer

What could be wrong with a check engine light on and O/D light flashing off in a 1998 ford explorer

You have a running code or its called limp mode if u have access to a obd2 scanner u can find your gremlin ! Thanks Chris

Sep 10, 2015 | 1998 Ford Explorer

1 Answer

I have a 2006 Chevy uplander, 3.5l, and when I turn the key to on position only the check engine symbol light's up on the instrument cluster and when turning key to cranking position nothing happens.

This is what would be done at the dealer or any good repair shop !
Perform the following preliminary inspections:
Ensure that the battery is fully charged. Refer to Battery Inspection/Test .

Ensure that the battery cables are clean and tight.

Inspect for any open fuses.

Refer to Power Distribution Schematics and Electrical Center Identification Views .

Inspect the easily accessible systems or the visible system components for obvious damage or conditions that could cause the symptom.

Ensure that the grounds are clean, tight, and in the correct location.

Refer to Ground Distribution Schematics and Power and Grounding Component Views .

Inspect for aftermarket devices that could affect the operation of the system. Refer to Checking Aftermarket Accessories .

Search for applicable service bulletins.

Did you find and correct the condition?
System OK
Go to Step 2


Install a scan tool.
Does the scan tool power up?
Go to Step 3
Go to Scan Tool Does Not Power Up


  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to establish communication with all of the control modules on the vehicle. Refer to Scan Tool Does Not Communicate with Class 2 Device for the modules you should expect to observe.
Does the scan tool communicate with all of the expected vehicle control modules
To ensure that retained accessory power (RAP) mode is inactive, if equipped, open the drivers door during the following step.

The engine may start during the following step. Turn OFF the engine as soon as you have observed the crank power mode.

  1. Access the Power Mode parameter on the scan tool.
  2. Rotate the ignition switch, operate the ignition mode switch, through all positions while observing the Power Mode parameter. Refer to Body Control System Description and Operation for a list of the power mode states that correspond with each switch position.
Does the Power Mode parameter reading on the scan tool match the ignition switch position for all switch positions?
Go to Step 5
Go to Power Mode Mismatch


Attempt to start the engine.
Does the engine crank?
Go to Step 6
Go to Symptoms - Engine Electrical


Turn the ignition to the START position.
Does the engine crank?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 3


  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Verify that the transmission is in Park or Neutral.
  4. With a scan tool, observe the IMS parameter in the powertrain control module (PCM)/engine control module (ECM) data list.
Does the scan tool display Park or Neutral?
Go to Step 4
Go to Range Selector Displays Incorrect Range


  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the Starter Relay Command parameter in the PCM/ECM data list.
  3. Turn the ignition to the START position.
Does the scan tool display Yes?
Go to Step 6
Go to Step 5
With all the modules on your vehicle you really need to start with a professional grade scan tool to see if all are communicating .

Aug 17, 2015 | Cars & Trucks

1 Answer

My 95 honda accord won't go past 50 mph

your vehicle is running in "safe mode" or in "limp mode"

do you know how to use a paper clip to jump the 2 terminals and access the honda's OBD1 trouble codes?

Check Engine Light Codes

eric used a piece of wire, but you can use a paper clip

Apr 13, 2015 | 1995 Honda Accord

1 Answer

1998 Chevy Suburban - service 4wd light comes on after running 4x4 for 2 mins

Well it could be the selector switch, but I doubt it.
Generally, the service light means something is not working that the computer controls. Solenoids and valves are a couple of possibilities.
The transfer case is shifted by solenoids commanded by the body computer based on the switch position on the dash.
You should be able to have a shop scan the body computer for trouble codes and proceed from there.
A basic code reader may not access the body computer.

Jul 05, 2012 | 1999 GMC Suburban

1 Answer

Set timing mode 1995 cadillac deville

Depending on the trouble codes, it may be the ECM. (computer)
You can have the car scanned for codes or attempt it yourself.
The "set timing mode" is the section of the computer program that you access to change the base timing. It should not show up on the display unless you access it.

Jun 26, 2012 | 1995 Cadillac DeVille

1 Answer


Pathfinders up to 1999 have the ecm under the front passenger seat. You access it from behind the seat, push the seat all the way forward. The flat head screw is on the left side of the ecm.

From 1996 on they switched to the OBD II system. So you can use a scan tool to access the codes. The connector is located at lower edge of instrument panel near steering column.
NOTE: 96 - 99 ecu's have different mode states:
1. (Mode I): with engine stopped, system in bulb check state. with engine running, system in malfunction warning state.
2. (Mode II): with engine stopped, system in self diagnostic results state. with engine running, system in front O2S monitor state.

BMW Custom Parts

Jun 06, 2012 | 1995 Nissan Pathfinder

1 Answer

Audi A6 3.0 tdi Quattro 2005, glow plug light comes on, limp mode

16619 -Engine boost condition - Limit not reached. Check intake hoses/ connections for leaks. Check Turbo charger waste gate regulating valve/ waste gate working correctly. Must move freely when accelerating, won't achieve full boost if waste gate sticking open. Check Turbo impeller turning freely, oil feed pipe for turbo can get blocked causing impeller to seize. Engine compact, not easy to access these components.

Jun 06, 2010 | 2008 Audi A6

2 Answers

On a 1994 dodge van what is a engine light code # 39 it causes the engine to run a little rough have changed the map sensor and idle air control valve.

its a hard code which has caused the vehicle to go into limp mode which is a safe mode for cars so to speak go to pep boys or wherever a scan tool can be accessed and have them clear it and they can tell you the code that was popping up

Jun 02, 2010 | 1994 Dodge B Series Cargo

1 Answer

My blazer does not blow any hot it does blow cold but also i'll put it on defrosters and it just continues to blow out of vents it wont switch out of vents.. any ideas?

Check the blender door:

Removal & Installation
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    • Connect the electrical connector to the actuator.
    • Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    • Turn the ignition switch to the OFF position.
    • Remove the actuator from the electrical connection.
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation
This is down under by your feet....

The other thing it may be with the heat is the heater water control valve:

Removal & Installation CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

  1. Drain the cooling system.
  2. Remove the access panel nut near the pollen filter.
  3. Remove the access panel.
  4. Remove the following components from the hot water flow control valve:
    • The vacuum hose
    • The remaining hose clamps
    • The remaining hoses
  5. Remove the hot water flow control valve.

To install:
  1. Install the hot water flow control valve.
  2. Install the following hot water flow control valve components:
    • The hoses
    • The hose clamps
    • The vacuum hose
  3. Install the access panel.
  4. Install the access panel nut until fully seated and not stripped.
  5. Fill the cooling system.
Heater water control valve

This is in your engine compartment.

Dec 01, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2011 Suzuki Grand Vitara Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides