Question about 1996 Audi A6

1 Answer

Sohc timing camshaft and crankshaft timing

Posted by Marcus Neswiswi on

Ad

1 Answer

Oscar

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 52 Answers

sohc timing - 88ab87a5-762b-44ba-bad2-cd7799f15863.png
you didnt mention the size of an engine, this is 2.8l petrol

Posted on Apr 16, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010CADILLAC NO POWER CODP0016


DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation

The engine control module (ECM) uses the crankshaft position (CKP) sensor and the intake camshaft position (CMP) sensor information to monitor the correlation between the crankshaft and intake camshaft position.

Diagnostic Aids
Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, crankshaft, or timing chain can cause this DTC to set.

Circuit/System Testing
Inspect for an incorrectly installed timing chain, excessive play in the timing chain, or for a timing chain that jumped teeth. Refer to Camshaft Timing Drive Chain Alignment Diagram and Camshaft Timing Drive Components Cleaning and Inspection .

Sep 18, 2018 | Cars & Trucks

1 Answer

I require a circuit diagram how to set my polo vivo 1.4 16v timing chain


THESE ARE THE TOOLS U NEED TO HAVE AND PROCEDURE!!GOOD LUCK AND BEWARE THE TIMING..REPLACE BOTH CHAIN AND TENTIONER!!!!!!

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-0.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-2.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-9.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-14.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-27.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-35.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-44.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-65.png

25525861-ziz4hbt0cga5mkppqv0kd4qd-2-77.png

Special tools and workshop equipment required
t Dial gauge -VAS 6079-
t Puller -T10094 A-
t Dial gauge adapter -T10170-
t Camshaft clamp -T10171-
t Counterhold tool -T10172-
t Locking pin -T40011-
t Spark plug spanner -3122 B-
t Counterhold tool -3415-
t Torque wrench (5...50 Nm) -V.A.G 1331-
Procedure
- Remove valve timing housing > Chapter.
- To turn crankshaft, reinstall bearing bush, crankshaft pulley -2- and crankshaft bolt -3- and securely tighten crankshaft bolt (use counterhold 3415).
- Remove spark plug from No. 1 cylinder. Use puller -T10094 A- and spark plug wrench 3122 B.
- Screw dial gauge adapter -T10170- into spark plug hole to stop.
- Screw dial gauge -VAS 6079- and extension -T10170/1- in to stop and lock in position with lock nut -arrow-.
- Turn crankshaft in direction of engine rotation, to TDC No. 1 cylinder. Note position of small needle on dial gauge.
- Then turn crankshaft back 45° opposite direction of engine rotation.
- Press tensioning guide rail -1- in direction of arrow and lock piston with locking pin -T40011-.
- Mark direction of rotation of timing chain -3- using felt-tip marker.
- Remove bolts -2- and remove camshaft sprocket -1- with timing chain -3-. Counterhold using counterhold tool -T10172-.
- Renew bolts -2-. Tighten bolt -2- to 50 Nm (use counterhold -T10172-).
- Turn inlet and exhaust camshafts until camshaft clamp -T10171- can be pushed into holes in camshaft to stop.
Locking pins -arrows 1- must engage in holes -arrows 2-. Inscription "TOP"-arrow 3- must be readable from above.
Note
Camshafts must not be pushed axially whilst turning.
- Install a M6 bolt -arrow- hand-tight (do not tighten) to secure camshaft clamp -T10171-.
- Remove camshaft sprocket bolts. It is absolutely necessary to use counterhold tool -T10172- for this.
Note
Camshaft clamp -T10171- must not be used as a counterhold tool.
- Remove one camshaft sprocket.
- Place timing chain over camshaft sprockets, observing chain direction of rotation, and install camshaft sprocket again.
- Tighten camshaft bolts until camshaft sprockets can still just be turned on camshafts.
- Tension timing chain by removing locking pin -T40011-.
- Turn crankshaft in engine direction of rotation to TDC No. 1 cylinder. Permissible deviation from TDC No. 1 cylinder: ±0.01 mm.
Note
If crankshaft is turned more than 0.01 mm past TDC, then turn crankshaft back 45° against engine direction of rotation. Then turn crankshaft in direction of engine rotation to TDC No. 1 cylinder.
- Hold camshaft sprockets -1- and -4- in this position with counterhold -T10172- then tighten bolts -2- to 50 Nm.
Note
Crankshaft must not move and timing chain -3- must remain tensioned on both sides when tightening camshaft bolts.
- Remove camshaft clamp -T10171-.
- Turn crankshaft two rotations in direction of engine rotation to TDC No. 1 cylinder. Permissible deviation from TDC No. 1 cylinder: ±0.01 mm.
- Insert camshaft clamp -T10171- to stop in camshaft openings.
If camshaft clamp -T10171- cannot be fitted
- Repeat adjustment.
If camshaft clamp -T10171- can be fitted
- Remove camshaft clamp -T10171-, hold camshaft sprockets with counterhold tool -T10172- and tighten bolts -2- a 1/4 turn (90°) further with a rigid wrench.
Note
Camshaft sprockets must not move on camshaft whilst tightening.
- Turn crankshaft two rotations again, in engine direction of rotation, to TDC No. 1 cylinder. Permissible deviation from TDC No. 1 cylinder: ±0.01 mm.
- Insert camshaft clamp -T10171- to stop in camshaft openings.
If camshaft clamp -T10171- cannot be fitted
- Repeat adjustment.
Further assembly is basically the reverse of the dismantling procedure. In the process, note the following:
t Installing valve timing housing > Chapter.
t Installing poly V-belt > Chapter.
t Renew oil seals for camshaft sealing cover and oil them before fitting.

Mar 06, 2015 | 2010 Volkswagen Polo 1.4

1 Answer

I am changing the timing chain in a 1993 Chevy S-10 with a 4.3L engine. I was told you have to disconnect a wire to reset it but I don't know where the wire is.


Timing Chain: Service and Repair
REMOVAL
Tools Required = Crankshaft Sprocket Puller
1. Remove the timing cover.
2. Remove the crankshaft position sensor reluctor ring.
3. Remove the camshaft sprocket bolts.
4. Remove camshaft sprocket.
5. Remove timing chain.
6. Remove the crankshaft sprocket.
7. Remove crankshaft sprocket key.

INSTALLATION
1. Install the key into the crankshaft keyway.
2. Use the crankshaft balancer installer to install the crankshaft sprocket.
3. Install the camshaft sprocket and timing chain.
4. Install camshaft sprocket bolts.
Be sure to align the camshaft and the crankshaft sprocket marks. Timing marks (Number 4 Firing).
Tighten bolts to 21 ft. lbs.
5. Align the keyway on the reluctor ring with the key in the crankshaft.
6. Install the reluctor ring onto the crankshaft until the ring is completely seated against the crankshaft sprocket.
7. Install the timing cover.

Don't know what Wire you are referring to.

Jul 30, 2013 | Cars & Trucks

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

Need to know what the timing marks and locations for replacing the timing belt


Timing Belt Removal & Installation 3.0L Engine To Remove:
Exploded view of the timing belt and sprocket assembly (3.0L engine) 86723255.gif

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
  3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
  4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
  5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference. Mark the direction of travel for the timing belt for correct installation 86723p72.jpg
  6. Loosen the timing belt tensioner bolt and remove the timing belt.
  7. If necessary, remove the timing belt tensioner. Turn the center tensioner pulley bolt until the timing belt has enough slack . . . 86723p73.jpg
    . . . then slide the timing belt off of the camshaft sprockets 86723p74.jpg
  8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
  9. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
To Install:
  1. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
  2. Install the crankshaft sprocket.
  3. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
  4. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
  5. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
  6. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
  7. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
  8. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side. NOTE: If the original belt is being reused, be sure to install it in the same rotational direction.
  9. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner. CAUTION
    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
    Rent or borrow the special tool to hold the camshaft sprockets steady . . . 86723p75.jpg
    . . . while loosening the center retaining bolt on the camshaft pulley, then . . . 86723p76.jpg
    . . . remove the camshaft sprocket from the end of the camshaft 86723p77.jpg
    Timing belt tensioner and spring positions 86723254.gif
    Timing belt routing and timing mark locations 86723256.gif

  10. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
  11. Install the crankshaft sprocket flange.
  12. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
  13. Rotate the crankshaft two full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
  14. Again line up the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 in. lbs. (28 Nm). Otherwise repeat the installation procedure.
  15. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
  16. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
  17. Install the accessory drive belts.
  18. Reconnect the negative battery cable.
  19. Run the engine and check for proper operation.
prev.gif next.gif

Aug 17, 2010 | 1997 Dodge Caravan

1 Answer

Installing a timing belt


Timing Belt and Sprockets REMOVAL & INSTALLATION Fig. 1: If you plan on reusing the timing belt, make sure you note the direction of the rotation before removal 91053p69.jpg Fig. 2: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts 91053p10.jpg Fig. 3: Camshaft alignment using the special service tool 91053g61.gif Fig. 4: Insert the crankshaft damper bolt to turn the crankshaft and . . . 91053p64.jpg Fig. 5: . . . align the camshafts and the . . . 91053g64.gif Fig. 6: . . . crankshaft before removing the old belt 91053p66.jpg Fig. 7: Loosen the timing belt tensioner pulley bolt, slide the tensioner back and . . . 91053p67.jpg Fig. 8: . . . tighten the bolt to the farthest right hand side as possible to hold the release the tensioner pulley so that the belt can be removed 91053p68.jpg Fig. 9: . . . remove the belt starting from around the camshaft pulleys 91053p01.jpg Fig. 10: Installation of the tensioner spring and retaining bolt 91053g62.gif For information on timing belt recommended replacement interval, refer to Section 1. CAUTION
The 2.0L engine is an interference motor. Extending the replacement interval could lead to the belt breaking and severe and costly engine damage. Care must be taken if rotating the crankshaft or camshafts with the belt off, if resistance is felt, do not force them to turn.
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers as outlined in this Section.
  3. Remove the valve cover.
  4. Place Camshaft Alignment Timing Tool T94P-6256-CH or equivalent, into the slots of both camshafts at the rear of the cylinder head to lock the camshafts into position. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  5. Loosen the camshaft timing belt tensioner pulley retaining bolt and move the tensioner pulley to relieve the tension on the timing belt.
  6. Temporarily tighten the tensioner in this position. NOTE: If the timing belt is to be reused, mark the belt for the direction of rotation before removing to prevent premature wear or failure.
  7. Remove the timing belt.
  8. If required, remove the sprockets as follows:
    1. Hold the camshaft with an appropriate camshaft sprocket holding tool.
    2. Loosen and remove the camshaft sprocket retaining bolt.
    3. Remove the sprocket from the camshaft.
    4. Repeat the procedure for the 2nd camshaft sprocket.
    5. Remove the crankshaft sprocket.
  9. Slide the crankshaft sprocket onto the crankshaft aligning the key-way.
  10. Align the camshafts using the Camshaft Alignment Timing Tool T94P-6256-CH. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  11. Reinstall the sprockets onto the camshafts and loosely install the camshaft retaining bolts.
  12. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  13. Loosely install the crankshaft pulley to verify that the engine is at TDC. Realign the marks if they have moved.
  14. Verify that the camshafts are aligned. NOTE: It is recommended to purchase a tensioner spring and retaining bolt through the dealer parts to apply the proper tension for used or new belt installations. The spring is bolted to the tensioner assembly and becomes a part of the engine. Ignore this notice if the tensioner spring is already installed.
  15. Reinstall the retaining bolt (W700001-S309) into the hole provided in the cylinder block and place the tensioner spring (6L277) between the bolt and the camshaft timing belt tensioner pulley.
  16. Tighten the retainer bolt to 71–97 inch lbs. (8–11 Nm) .
  17. Remove the crankshaft pulley and install the timing belt onto the crankshaft sprocket, then onto the camshaft sprockets working in a counterclockwise direction.
  18. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  19. Be sure that the span of the camshaft timing belt between the crankshaft sprocket and the exhaust camshaft sprocket is not loose.
  20. Be sure that the camshaft timing belt is securely aligned on all sprockets.
  21. Reinstall the lower timing belt cover and tighten the retaining bolts to 53–71 inch lbs. (6–8 Nm) .
  22. Apply silicone sealer to the key-way of the crankshaft pulley and install. Tighten the retaining bolt to 81–89 ft. lbs. (110–120 Nm) .
  23. Inspect the timing mark on the crankshaft pulley to verify that the engine is still at TDC.
  24. Loosen the camshaft timing belt tensioner pulley retaining bolt and allow the tensioner spring attached to the pulley to draw the tensioner pulley against the camshaft timing belt.
  25. Remove the camshaft alignment timing tool from the camshafts at the rear of the engine.
  26. Turn the crankshaft two revolutions in a clockwise direction.
  27. Tighten the camshaft timing belt tensioner pulley retaining bolt to 26–30 ft. lbs. (35–40 Nm) .
  28. Recheck that the crankshaft timing mark is at TDC for the No. 1 piston, and that both camshafts are in alignment using the camshaft alignment timing tool. NOTE: A slight adjustment of the camshafts to allow the insertion of the camshaft alignment timing tool is permissible as long as the crankshaft stays at the TDC location.
  29. An appropriate camshaft sprocket holding tool can be used to move the camshaft sprocket (s) if a slight adjustment is required.
  30. If a camshaft is not properly aligned, perform the following procedure:
    1. Loosen the retaining bolt securing the sprocket to the camshaft while holding the camshaft sprocket from turning with the sprocket holding tool.
    2. Turn the camshaft until the camshaft alignment timing tool can be installed.
    3. Verify that the crankshaft timing mark is at TDC for the No. 1 cylinder.
    4. While holding the camshaft sprocket with the camshaft sprocket holding tool, tighten the retaining bolt to 47–53 ft. lbs. (64–72 Nm) .
    5. Remove the tool and rotate the crankshaft two revolutions (clockwise) .
    6. Verify that the camshafts are aligned and that the crankshaft is at TDC for the No. 1 cylinder.
  31. Install the valve cover.
  32. Install the timing belt covers.
  33. Connect the negative battery cable. prev.gif next.gif

Aug 17, 2010 | 2000 Mercury Mystique

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1996 Audi A6 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14846 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...