How to shut off abs light

tcsd and abs work of sensors on all wheels so check for wiring and connections
brake light ( on dash) can be low fluid level in the brake reservoir, hand brake still on
run the fault codes to find exact codes that are putting the lights on

PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

You will need access to a scan tool that "talks" to the ABS module. As for the fix, it depends on what the diagnosis tells you.

First, check to see if your ABS and your TCS fuses are good. A lot of times, if both lights come on, it senses a failure in the braking system. Your vehicle will disable the abs if it finds a problem in the braking system, hence the red brake light/hand brake light coming on in the dash. Get a code scanner that also reads the abs module. You could have a bad wheel sensor, which is tied to your TCS and your ABS system. Either that, or you ABS module could be bad.

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Hello: If there is a problem in the ABS it will bring on the tcs light as well. To determine what is causing the problem you need to have the ABS checked with a scanner to get the code. Then trouble shoot the components that the code leads you to. Normal braking is available with the light on but TCS is not as it relies on ABS for functioning the TCS.

abs=anti-lock brake system/ tcs=traction control system ==sounds like you have a problem with ur abs possible bad sensor or a wiring connection problem when abs shuts down [trouble light] your brakes will work normal but if u stomp or brake hard the brakes will lock up skid and the tcs doesnt affect brakes but if u accelerate hard tires will spin lose traction check the wiring and connections to the sensors sometimes debris hits the wire and loosens the connection if looks ok and light is on have car scanned for the trouble code most auto stores such as auto zone/advanced auto offer this service for free the code will what and where the problem is so repair can be made

some markets have a button on the dash with tcs/abs and a dash light saying "tcs off".if your car has not got the button then you cant turn it off(germany yes.uk no)abs/tcs should only be turned off in deep snow,otherwise best left alone,unless you have been taught how to drive with/without.....(on ice you wants the wheels to turn,on snow you want the snow to wedge to slow you down......)see what i mean???