Change Headlight bulb mb100 van - M-Class Mercedes-Benz Cars & Trucks

You should see a large plastic wingnut holding the entire headlight assembly to the fender. Remove that and pull the headlight assembly straight out. Then you can access the turn signal bulb

Here's a link on replacing your light bulb on your VW. Sparky Answers 2001 VW Beetle Changing The Low Beam Headlight Bulb HERE'S A VIDEO,ALSO How To Change Head Light Bulb VW Beetle

Instructions

1. Make sure the the headlight switch is in the off position.
   
2. Open the bonnet to the Escort.
   
3. Locate the back side of the headlight assembly to the headlight that needs to be changed (driver's side or passenger side) from inside the front the engine compartment.
4. Unplug the wires from the back of the bulb.
5. Turn the back of the bulb housing counterclockwise one-third of a turn until the bulb and wire harness are released from the headlight assembly.
6. Unplug the wire harness from the bulb socket.
7. If using Halogen headlight replacement and be careful not to touch the glass bulb part. Handle it by the socket at the bottom of the headlight.
8. Plug the wire harness into the new headlight replacement.
9. Align the tabs on the headlight housing to the slots in the headlight assembly and insert the bulb into the assembly. Twist the headlight one-third of a turn clockwise until it locks into place.

To replace headlight bulb of kia pregio van: You only need Phillips screw driver and 10mm socket or open wrench. Open the hood, remove front grill with 4 phillips screw. This will give you room for your hand to pull out the headlight housing later on. Next is remove the signal light housing by unscrewing the phillips screw on top of the headlight housing then pull out the signal light housing and remove the bulb. You will see 2 pcs 10mm bolts on the side which hold the headlight. Loosened and remove the bolts on headlight holder then pull the headlight sideward. Remove power supply socket before removing it completely from the van. Remove bulb socket, spring clip, and busted bulb and replace with new one. Reassemble the disassembled parts in reverse order. That's it, will take you only 10 minutes.

this is not uncommon for these vans. when you install the headlamps be sure not to touch the bulbs with bare hands. use latex gloves. the oil from your hands will diminish the life of the bulbs. when your done with the bulb issue have your charging system checked for an overcharge(anything over about 14.7 volts). if the charging system is in good shape, i would seriously consider the quality of the bulbs. happy holidays

1.) Open the hood of your van
2.) On the passenger side of the vehicle, look behind the headlight enclosure. You will see a set of wires running into the back of it. This is the power clip. Either with your hand or a flat-head screwdriver, pop the power clip off.
3.) There is a plastic ring encasing the light bulb. Turn the ring counter-clockwise and pull it out of the socket and set it aside.
4.) Pull firmly on the light bulb to remove it.
5.) Place the new light bulb into the same opening. Be careful not to touch the glass part of the new bulb. The oils in your skin can substantially reduce the life of the new bulb.
6.) Replace the plastic ring and turn it clockwise to lock it in place.
7.) Reattach the power clip to the back of the bulb.

if you have a owners manual its in there, if not there is a pin and a screw on top on headlight assm. you take out and assm. pulls out to access headlight and turn signal bulbs.

Open the engine hood and you'll see there is a plastic housing holding the head light ans side light to the frame. There are two wing nuts and one wing bolt holding it all together. Remove those and pull the headlight and side light housings out from the frame. You'll be able to access all of the lights now.

There is one 10mm Bolt on the top of the light and three 10mm nuts on the back of the light. You will need to use a 10mm wrench to remove the nuts because they are in a tight place.

After the 1 bold and 3 nuts are removed, the entire headlight assemble will pull straight out. You don't need to take the headlight bulb out because there should be enough wire to pull out the assembly far enough to get to the turn signal bulb. This will allow you to change the turn signal bulb which should be a 4157 amber bulb.

When putting the headlight assemble back in the van, there is a plastic pin in headlight assembly that goes into a hole in the front fender for alightment. Don't force the light. Take your time and the headlight assembly will go back in the van smoothly.

under the hood unplug the headlamp bulb twist off the sleeve that holds the bulb and pull out the bulb assy do not touch the glass of the bulb when installing the new one