Question about 1995 GMC Sonoma

1 Answer

Motor mount how can i change the mounts without a lift/cherry picker?

Posted by joseph on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

Put a jack under motor to support the motor then replace. Might want to put a 2x4 and some rags or blanket between motor and jack to prevent damage

Posted on Mar 28, 2014


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I replace the motor mounts on my 2001 Toyota Camry Solora xle v6

Ok, first off apply E brake. Second, locate motor mounts usually on side bottom, connect to frame. Third jack up car place jack stands. Fourth,disconnect all wiring, maf, pretty much anything and everything that will get in way. Fifth, grab cherry picker, connect engine to cherry picker. Sixth, disconnect engine from trans, or leave connected but might be more difficult for some. Seventh,unbolt engine from mounts(usually 3or so bolts on each mount), do not rock engine, raise cherry picker(or crane some call it different)when tension on chain slowly rock engine. Should pop out unless you missed a bolt.

Feb 20, 2015 | 2001 Toyota Camry Solara

1 Answer

Do I need to remove the engine from my 2001 4.3 V6 blazer in order to get the oil pan off?

Two ways no need to pull engine
One lets start with cherry picker engine hoist unbolt mounts slide bolts
Lift to desired height of two inches 4x4 accross inner tire wells now chain down to 4x4 pull pan off 10 minutes done
The other way is mobile home jack stands under motor mounts and mounted 4x4 at top chained down never on the front clip but on inner tire well
They make a specific engine lift on wheel wells for this your not lifting engine high enough but enough to get the pan off safely

Oct 24, 2014 | 2001 Chevrolet Blazer

1 Answer

What would it cost a mechanic to install motor mounts on a 1995 gmc sonoma 4.3 litre 4*4

Im sure your 95 is no different then my 01 sonoma 4x4 u shouldn't need a cherry picker to do the engine mounts a small block of wood and a floor jack to support the engine from underneath and take a little bit of the load off the mount should work you dont have to lift the engine out to do them its not easy this way but is possible and cost less money working for a gm parts department and a former tech you would be spending and average of 75 to 100 an hour labor wise depending on what shop u take it to and what shop labor rates at like near you I would estimate an easy 2 hours labor but it all goes by book time thats or determined at the shops

Mar 27, 2014 | 1995 GMC Sonoma

1 Answer

Changing out transmission mount on a 96 dodge intrepid

this is a fairly easy fix, youll need to undo the mount bolts and with a jack from the bottom or a cherry picker from the top lift up the ****** enough to wiggle the mounts out (or drop the ****** if they are top mount) you may also need need to loosen the motors mounts to allow everything to move as well as remove the half shafts from the transmission to allow movement. depends on how far you need to move it in order to wiggle the mounts out. i always reccomend buying a haynes or chilton repair manual. as it covers step by step how to perform alot of these repairs in simple step by step format (if you can bake a cake by direction then you can work on a car) and they are ussually around 10 to 15 bucks. not a bad investment. hope this helps! good luck

Feb 12, 2012 | 1996 Dodge Intrepid

1 Answer

How to change the motor mounts on a 2004 sedona

Loosen motor mount bolts, raise engine off mount/s (with a cherry picker or carefully with a floor jack with a block of wood on it). Remove old mount/s. Put the new mount/s in place on block, inserting the bolts, but not tightening them just yet. Use a rolling head pry bar (or whatever you have that works) to align the mount/s with the frame bracket/s and bolt hole/s. Now you can tighten the bolts. Hope this helps you.

Aug 24, 2011 | 2006 Kia Sedona

2 Answers

How do you remove a oil pan from a 1984 z28 camero

Drain the oil completely, remove all the bolts and drop the pan. On 84 I don't believe you have to remove the tranny. Just remove the bolts.

You can go to and signup for a free account. Then login to the account, choose your vehicle year, make, model, and engine size. Finally click on view repair manual. Now you have a free repair manual for your vehicle.

Apr 28, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

Do i have to remove motor mount in order to change serpentine belt on 97 pontiac bonneville 3.8 liter not the super charged. any tips or advice would be greatly appreciated

If you remove a motor mount without a cherry picker or hoist holding the engine in place, you run the risk of crushing yourself under your car. Each motor mount is two separate pieces of metal held together by a fairly large bolt in the middle. One end of one piece is attached to the engine block the other is attached to the frame of the vehicle. But I would suggest not attempting this without someone's help that knows how to do this. If you're not sure where the motor mounts are it leads me to believe that you will either break an expensive part or kill yourself.

Mar 16, 2011 | 1997 Pontiac Bonneville

2 Answers

Can't remove the alternator! How do you remove the alternator on a Ford Focus 2001 without unbolt the engine mount?

The other option, but be warned could cause damage to the motor mounts, is to use a cherry picker to lift the engine up enough to clear the alternator from the engine bay.

Sep 11, 2010 | 2001 Ford Focus

1 Answer

How do i lift the engine soas to change motor mounts

Usually the best way is to use a jack with a piece of wood under the oil pan. You should be able to jack up the motor far enough to remove the mounts. Or a engine hoist (cherry picker) can be used.

Apr 28, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

Replacing motor mounts

It's not as easy as it sounds. Basically you will need to lift the engine off the frame and unbolt the old ones off. I highly doubt that you can do this without disconnecting the transmission. Definitely something that you want an experienced mechanic to help with. It may just not be worth it. If you can lift the engine with the transmission attached (if there is enough room to tilt it up), that would be the best bet but you will need an engine hoist or cherry picker to do this. (THIS IS NOT FOR AN AMATEUR)

Let me know if you have any further questions, this will require a lot of work

Aug 14, 2008 | 1984 Chevrolet Celebrity

Not finding what you are looking for?
1995 GMC Sonoma Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1256 Answers

john h

Level 3 Expert

23515 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides