HOW TO REPLACE OR REPAIR WHEEL SPEED SENSOR

DTC C0040 Right Front Wheel Speed Sensor Circuit --
Conditions for Setting the DTC
C0035 C0040 C0045 C0050
One of the following conditions exists for 0.02 seconds:
• A short to voltage in the wheel speed sensor signal circuit.
• An open in the wheel speed sensor signal circuit.

Diagnostic Aids
C0035 C0040 C0045 C0050
If the customer comments that the ABS indicator is ON only during moist environmental conditions (rain, snow, vehicle wash, etc.), inspect the wheel speed sensor wiring for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of water intrusion by using the following procedure:
Spray the suspected area with a 5 percent saltwater solution. To create a 5 percent saltwater solution, add 2 teaspoons of salt to 354 ml (12 oz) of water.
Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
If the DTC returns, replace the suspected wheel speed sensor or repair the wheel speed sensor wiring.
Rinse the are thoroughly when completed.


Replace the EBCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the repair?

Do yourself a favor an take it to a qualified repair shop . You need a factory scan tool to see these code's
DTC C0040 00 : Right Front Wheel Speed Sensor Circuit No Additional Information
DTC C0040 0F : Right Front Wheel Speed Sensor Circuit Erratic Signal
DTC C0040 18 : Right Front Wheel Speed Sensor Circuit Signal Amplitude Less Than Minimum

DTC C0899: Device Voltage Low
Circuit/System Description
The electronic brake control module (EBCM) monitors the battery voltage level available for system operation. A low voltage condition prevents the system from operating properly.

Circuit/System Testing
Measure the voltage at the battery terminals.
With scan tool, read the battery voltage in the EBCM data list.
? If less than 10 volts, test the ground circuit of the EBCM for high resistance. If the circuit test normal, test or replace the EBCM.
Go to Battery Inspection/Test and Charging System Test .

I don't think so? The first two codes are for left and right front wheel speed sensors. The last code is for abs system, the codes are all connected.
Make sure the wheel speed sensors are connected and clean. Just my opinion. Depending on the issue, you may need more diagnostics on the abs system?

C0040
Right Front Wheel Speed Sensor Circuit Malfunction
EBCM
DTC C0035-C0051

The wheel speed sensor produces an alternating current signal whose amplitude and frequency vary, depending on the velocity of the wheel. The electronic brake control module (EBCM) uses the frequency of the AC signal to calculate the wheel speed.

This wouldn't have anything to do with not starting ! Won't start how ? When you turn the key to the start position what happens ? Does the starter engage an spin the engine ? This would be a crank no start , now if nothing happens when you turn the key this is a no crank - no start .

It is the right front (RF) ABS sensor that this codes corresponds to nothing to do with the rear.. Are you using a GM TECH 2 scanner? If not that is the problem.

C0035 is ABS Sensor in left front wheel
C0040 is ABS Sensor in right front wheel
C0201 is ABS Enable Relay Contact Circuit
You most likely have a poor ground connection or a faulty EBCM (Electronic Brake Control Module) for these conditions. I recommend having someone run a diagnostic test at a shop. I doubt the ABS issue is stopping the truck from cranking.

Faulty Right Front Wheel Speed Sensor C0040
- Right Front Wheel Speed Sensor harness is open or shorted
- Right Front Wheel Speed Sensor circuit poor electrical connection

Will be located near the wheel hub. As long as there is no physical damage I would guess you will be replacing the sensor

I agree that it is more then like the the hub bearing assembly that also houses the speed sensor I would first check that there is no damage to the wiring that goes to the hub bearing that could be easy repaired, or debri that has been caked in between the sensor & the hub, use an air preesure to clean it out. Hub bearings are very expensive, so try this first. Good luck

Sounds like you need front wheel speed sensors. Replace the wheel bearings and sensors. May have an ABS unit fault, but more likely is both wheel bearings/speed sensors.