Wiper motor r/r 2002town&country

If it frozen, that rules out a disconnected linkage. Unfortunately, this is a little known model and whereas I can always find fuse box diagrams, for yours I can't. If you have a test meter, you can test all the fuses without removing them by testing for continuity at the two contacts on the top of the fuse. It may also be the relay.

https://www.google.com/search?q=volkswagen+routan+fuse+box+diagram

https://www.google.com/search?q=volkswagen+routan

Google thinks it might be this as apparently they are a badged Chrysler. If it is it is this fuse J20.
J20 30 Amp Pink - Front Wiper LO/HI

Fuse Box Diagram Chrysler Town & Country (2008-2016)

https://fuse-box.info > chrysler > chrysler-town-country...

Fuse box diagram (location and assignment of electrical fuses) for Chrysler ... Rear View Mirror (RR VW MIR), Cabin Compartment Node (CCN), Transfer Case .....

wipers won't work??? - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusFeb 15, 2012 - 1998 Chrysler Town & Country LXi My windshield wipers won't work. The turn ... I have a Plymouth Horizon & the same problem, but I'm fairly sure it's theswitch on mine. ... Ended up taking it to the dealership - it was a wiring problem from the body control module to the switch. ... Used Dodge Caravan".

Auto Repair : How to Test a Windshield Wiper Motor ...

? 3:04
https://www.youtube.com/watch?v=7EliY2Hwj0E
May 12, 2009 - Uploaded by ehowauto
In order to test a windshield wiper motor, the first thing to do is to make ... He said its the relay and the entire ...

Windshield Wiper Motor Replacement : How to Access a ...

? 3:37
https://www.youtube.com/watch?v=iVBAvvfc1FU
Oct 1, 2008 - Uploaded by expertvillage
Removing windshield wiper arms and intake grading is essential to gaining access to the windshield wiper

The wiper module is built into the the wiper motor. First unplug it(on the drivers side, just under the wiper cowling) Look for corrosion. Clean it with battery cleaner, the plug and motor connector. If it still acts up. replace the wiper motor.

yes

Sounds like the park switch in the wiper motor is bad.Some manufacturers allwo you to change the circuit board seperately from the motor,sometimes they have to be changed as a unit

The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:

1. Before servicing the vehicle refer to the precautions at the beginning of this section
2. Remove the wiper arm finish caps
3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
4. Remove or disconnect the following:
   • Wiper arm retaining nuts and washers
   • Wiper arms
   • Weather-strip at rear of hood
     
     
     
     
   • Grill nuts from base of wiper arm shaft
   • Grill
   • Electrical harness connector from the wiper motor
   • Wiper motor retaining bolts
   • Wiper motor assembly from plenum area
   
   
   
   
   
5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
6. Remove the wiper motor from the transmission assembly

To Install:

1. Install or connect the following:
   • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
     
   • Wiper motor to plenum area
   • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
   • Electrical harness connector to the wiper motor
   • Weather-strip at the rear of hood
   • Grill
   • Grill nuts to the base of the wiper arm shaft
2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
4. Install the wiper arm finish caps
5. Verify correct wiper system operation

Remove the wiper arms (pop off the caps at the base) and the 15mm nut. Take out the screws that hold down the wind shield cowl lift it away to expose the washer hoses. Unplug the wiper motor (center driver's side) by pulling out the red clip on it and squeezing the tab. Remove the 13mm nut from the wiper motor idler arm and take out the 3 10mm bolts that hold it in place. Squeeze it out from under the wiper transmission, or loosen the lower bolts. You'll see them. Not a difficult job, just take your time.

Hope I've helped.

Front Wiper Motor Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the windshield wiper mounting arm and pivot shaft
   WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
   NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
   
3. Remove the 3 bolts and the wiper motor.
   
   
   
   Fig. Wiper motor and linkage
   

To install:

1. Install wiper motor and bolts.
2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
3. Install windshield wiper mounting arm and pivot shaft.
4. Check wiper operation.

Rear Wiper Motor - Removal & Installation

1. Remove the rear pivot arm.
2. Remove the rear wiper motor shaft nut cover
3. Remove the rear wiper motor shaft nut.
4. Open the lift gate window.
5. Remove the rear wiper motor cover trim panel.
6. Disconnect the electrical connector.
7. Remove the 2 rear window wiper motor nuts
8. Remove the rear window wiper motor.
   
   
   Fig. Rear wiper motor view-2008 model shown, other years similar
   

To install:

1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
2. Reconnect the electrical connector.
3. Install wiper motor cover trim panel.
4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
5. Install shaft nut cover.
   
6. Check wiper operation.

Good luck (remember rated this post).

Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:

1. Disconnect and isolate the negative battery cable.
2. Remove the rear wiper arm.
3. Open the liftgate.
4. Perform the following to remove the liftgate trim panel.
   • If equipped, remove the lift motor link
   • Remove the upper frame molding
   • Remove assist handle screws
   • Disengage the hidden clips around perimeter of liftgate trim
   • Disconnect the electrical connectors.
5. Disconnect the wire connector from the wiper motor.
6. Remove the wiper motor mounting screws.
7. Remove the wiper motor.

To Install:

1. Position the wiper motor in the liftgate.
2. Install the wiper motor mounting screws.
3. Connect the wiring connector.
4. Install the liftgate trim panel.
5. Close the liftgate.

there is a plastic cap where the arm connects to a post. pop this cap off with your finger nail or small screw driver. this cap hides a nut. remove the nut (10mm socket needed?) and pull the arm off to replace the blade