Question about 2004 Chevrolet Tracker

Open Question

Pull rear brack brack drum

Pull rear brack drum

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear brack light stays on my honda vtx 1300

Brake pedal switch may be stuck or worn out .

Oct 06, 2017 | Honda Cars & Trucks

1 Answer

Cant get the rear brack drum off

You will need to back off the rear brake bands to get them to clear the wear on the drum. The drums should come off with little resistance.

Apr 10, 2016 | Cars & Trucks

2 Answers

How do you remove rear break drums from 1976 chevy 4x4 c20

Take the tire off and look on back side of drum they should have a lil black rubber pull rubber out and get a flat head screwdriver u will have to go up r down wit it to Los up r brack pad and pull off the drum

Mar 04, 2015 | Chevrolet Cars & Trucks

1 Answer

I have a 2005 toyota tundra v8 and when i put the truck in reverse and drive it, it squeeks. but if i wet the back axel and the back of the brakes it eventually goes away for a couple of days and comes...

hi,if it has drum bracks it could be brack dust inside the drum,if its disk bracks they might need copper- slick put on the brack pades,on the side that faces the brack-caliper.
hope this was some help.

Oct 29, 2013 | Toyota Cars & Trucks

1 Answer

My maruti esteem 1000 car rear wheel break drum is ceased ,I opened the rear wheel but stucked as there is a cover over the brack assembly , please help me how to open this cover

There will be two threaded holes provided on the drum.
Try to open using an M8 bolt. Because of long time drum get struck because of rust, mud ect.. These holes are provided to open the same

Oct 10, 2013 | Maruti Cars & Trucks

1 Answer

2001chevy truck 1500sereis emergy bracke shoes with disc brackes

Those work pretty much the same as a conventional drum brake. The main difference is that you must first remove your brake caliper and caliper bracket assembly so you can get the rotor off.

Then it is only a matter of removing the return springs and hold-dow clips just as in a regular drum brake. (See Picture)


Mar 19, 2012 | Cars & Trucks

2 Answers

Grinding noise from rear and rear brack hub hot

Collapsed rear wheel bearing or worn brake shoes or pads. You will need to pull the wheel and hug off to check both.

Jan 16, 2011 | 2002 Kia Rio

1 Answer

How do you get back brack drum off, do you have to remove center nut

In the center of the hud, there is a steel cover. use a screw driver and a hammer to tap the cover off. Make sure you take the handbrake off, and undo the center nut and take the bearings out. when you pull the hud off.
When you come to put it back on make sure you put the bearing in first then the washer then the nut.

I hope this has helped!

Jul 09, 2009 | 2000 Ford Focus

1 Answer

Right rear wheel has rubbing and grinding noises, as on cast iron

My advise is to adjust the rear brakes. The drum should not move in a side to side fashion. adjusting the brakes will also more than likely take care of that anti lock brake light also. adjust the brakes up to where the rear wheel will spin but you should be able to hear the brake show dragging slightly on the drum.

Apr 06, 2009 | 2001 Mitsubishi Eclipse Spyder

1 Answer


Look at either a Haynes book or Chilton book, try the library thye usually have the books. Most have the pictures that are basically the same for all rear drum type brakes.

Mar 28, 2009 | 1991 Dodge Dakota

Not finding what you are looking for?
2004 Chevrolet Tracker Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides