Plymouth Grand Voyager SE, 1997. 3.0 litre

Search Results

My windshield wipers only work on high speed...? ' Yahoo Answers

https://answers.yahoo.com/question/index?qid...
Nov 11, 2006 - My windshield wipers only work on high speed. ... If it's the compound switch on the lever on the steering wheel, it can be a bit complicated to ...

Windshield wipers - CarGurus

www.cargurus.com > Questions > Mercury > Grand Marquis

CarGurusMay 19, 2015 - Windshield wipers - My wipers stopped last week and the next day they ... slow or intermitt and only work on high speed and the washer wiper doesn;twork ... The LCM does not effect the operation of the motor or switch it just ...

Windshield Wipers only working at highest setting - Ford Flex Forum

www.fordflex.net > ... > General Ford Flex Discussions
Feb 16, 2011 - Windshield Wipers only working at highest setting ... rear wiper worksjust fine, just the front wipers only work at highest setting. ... the wipers sometimes grinds out the gears thus only working at high sppeds. If it is the motor or Transmission for the wipers, can I fix this myself and how much would it cost me.

Common GM Wiper Problem - YouTube

? 3:23
https://www.youtube.com/watch?v=kc6e2Tmar68
Oct 25, 2010 - Uploaded by roadragecustoms
The windshield wipers only worked occasionally. ... My 1998 dodge ram wipers only work on high will this help me? thanks.... Express van. you have to take out the motor and the transmission from under the front of the van..

Well I would guess its the contacts in the switch itself since they get moved manual by your hand the most. A motor either works or don't work no mater what speed its running..Just trying to help

That would be the sensor on drivers side closest to front of vehicle or in front of catalytic converter.Hope this helps!!

Try doing a "Brain Kill" on the van. Disconnect both battery terminals, and (MAKE SURE THEY ARE NOT CONNECTED TO THE BATTERY!!!!!) touch and hold them together for at least 10 seconds. Mopars hold onto their faults, even after the repairs. Huge problem for transmission shops, but that's another topic. My 99 Dakota had the Speed Sensor fail, and it wouldn't shift until I "Killed" the ECM and BCM's memories.

Good Luck!!!

Remove the arms,and place them back on where they need to go,do not turn the wipers on,do this as they set now.If the wiper blades when turned on go off the left side of the windshield ,then you will have to remove everything again,and move the wipers down in the rest position,and align everything up to the rest position,with the wipers at rest,and the motor at rest.

Remove windshield wiper blades (mark the arm and stud to put back exact). The next two steps you might have to lower/raise the hood. Remove cover just below the windshield(each end has a phillips screw turn 90 degrees so arrow points toward center of van). Remove the 4 metal braces. Remove windshield wiper motor/linkage assembly(the whole tray comes out). Remove drive belt. Disconnect negative side of the battery. Remove alternator horizontal mounting bracket. Loosen vertical bracket bolts to get to electrical connectors. Finish removing bolts and alternator.

the delay switch on the wiper motor may have went bad, the only way to fix it is to replace the wiper motor. for (i have the same problem),your computer may be shot or you have a faulty wiring harness.

check the fuse then the relay then the switch.

wiper motor would be your point of interested to begin!

Sure pull the cover off the arm at the base(by the bottom of the windshiel) under that you will find a bolt. Unbolt the arm and pull it off then adjust both arms so that they do not entangle at the high point. You can turn on the wipers and when they reach the high end quickly shut off ignition they will stop at this position so you can adjust them, This is what we would do at the shop for about 200 bucks. Take your time and be sure to tighten everything up when you're don and you will do great. Have fun.