Transmission Drops out of overdrive to drive when at speeds over 50 mph. It wont go back into overdrive until i shut the engine off and restart. Also after it does the dropping out of overdrive, when i come to a stop, it does not downshift to low gear to start out, I manually have to shift it thru the range, 1st, 2nd then drive.

I really need to know what size engine you have in your Beretta as well as how many gears are on the shifter as in low one low two Drive with a circle around it or one two three drive with a circle around it sounds to me like a torque converter pressure switch when vehicle is shifting into overdrive switch is not operating correctly releasing pressure from torque converter causing vehicle not to have enough counterweight for transmission until vehicle slows down and then will operate again shifting through gears until the Overdrive goes to kick in send more info

it is immaterial when the over drive is to be used
If the constant shifting is annoying you then switch it off
The over drive is just that
an extra high final gear in the transmission to reduce the engine rpms at high speed to save fuel . It can be set for automatic engagement or turned of if pulling heavy trailers or caravans or carrying full loads and so save wear on the transmission

Roger, that doesn't even make a whole lot of sense to me. If the overdrive is causing the transmission to slip, wouldn't it also cause the fuel mileage to go down? Are you sure the transmission is slipping? Or is the transmission simply shifting in and out of overdrive? If it is, is it shifting at the proper speeds? Driving at around 40 - 50 Mph will sometimes make the transmission go in and out of overdrive repeatedly. This can be perfectly normal.

Have you checked your transmission fluid level?

Is your overdrive off light flashing? If the transmission is actually slipping the OD OFF light should be blinking at you to let you know there is a transmission problem. Either that, or the Check Engine light will be coming on. In either of these cases, you need to scan your onboard computer network for possible fault codes.

takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

might want to check the speed sensor, also look for any vacum leaks, since it sounds like it only happens below 50 mph.

Transmission !!!!!!!

have a 1998 K3500 silverado 4x4 with 454 motor and 4L80E transmission. I can not get over 55 or 60 mph. At that speed the transmission down shifts from 4th (OD) to 3rd. The speedometer also drifts from about 50 to 65. If I try to speed up it will down shift to 3rd. I have replaced the VSS on the trasfer case. Is there another speed sensor somewhere? Or could it be the TPS? The truck drives and shift normal up to this point. where should i look next. thanks

Try this relearn procedure hopefully it will help

Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Many vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. The computer will use default data until new data from each key start is stored. As the computer memorizes vehicle operation for each new key start, driveability is restored. Vehicle computers may memorize vehicles operation patterns for 40 or more key starts. Customers often complain of driveability problems during the relearn stage because the vehicle acts differently then before being serviced. Depending on the type of vehicle and how it is equipped, the following complaints (driveability problems) may exist:

Harsh Or Poor Shift Quality
Rough Or Unstable Idle
Hesitation Or Stumble
Rich Or Lean Running
Poor Fuel Mileage

These symptoms and complaints should disappear after a number of drive cycles have been memorized. To reduce the possibility of complaints, after any service which requires battery power to be disconnected, vehicle should be road tested.

Vehicle Preparation

Ensure all components are connected. Ensure transmission fluid level is correct. Warm engine to normal operating temperature. If vehicle has been repaired, perform KOEO and Continuous Memory Code Self-Test and ensure fault codes are not present.

Computer Relearn Procedures

Idle Relearn Procedure

Place automatic transmission in Park or manual transmission in Neutral position. Ensure the emergency brake has been set and all accessories are turned off. Start engine and bring to normal operating temperature. Allow manual transmission vehicle to idle in Neutral for one minute. Allow automatic transmission to idle in Neutral for one minute and then to idle in Drive for one minute. Once initial relearn is complete, process will be completed during normal driving. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (AOD-E, AXOD & AXOD-E TRANSAXLES)

With transmission gear selector in Overdrive, moderately accelerate vehicle to 50 MPH for a minimum of 15 seconds. Transmission should be in 4th gear. While holding speed steady, lightly apply and release brake for about 5 seconds. Stop and park vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.

Drive Cycle Test (E4OD)

With transmission gear selector in Drive, press Overdrive Cancel Switch (LED should light). Moderately accelerate vehicle to 40 MPH for a minimum of 15 seconds (30 seconds above 4000-ft. elevation) Transmission should be in 3rd gear. While holding speed steady, press Overdrive Cancel Switch (LED should go off) and accelerate from 40 MPH to 50 MPH. Transmission should shift from 3rd gear to 4th gear. Hold speed steady for 15 seconds. While holding speed steady, lightly apply and release brakes enough to turn brake lights on. Maintain 50 MPH for about 5 seconds. Stop vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.