DOOR LOCKS SUDDENLY UNLOCK WHEN CAR IS IN MOTION

2009 LTZ/Cycling (on/off) Door Locks - Chevy Malibu Forum ...

www.chevymalibuforum.com/forums/showthread.php?t=6599

10 posts - ‎8 authors
02-17-2011, 07:26 AM ... Two or three times while driving( in motion) the door lockswill cycle two or three times through the lock/unlock positions and then will stop. ...Since i can't produce this glitch on demand there is no point taking it to the dealer. ...The Malibu system will not let you lock the doors when the door is open.

Door Lock Actuator Recall? - Page 4 - Chevy Malibu Forum ...

www.chevymalibuforum.com/forums/showthread.php?t=7950&page...

Sep 23, 2011 - 10 posts - ‎7 authors
When I was driving this afternoon, the car would unlock itself at random intervals. ... It is reasonable to expect that Chevy could design a car whose doors remain locked while the car is in motion. ... 2009 Malibu 2LT, Adopted 5-7-2011 ... If you can get them to replace ALL 4 of them for a $100 deductible, I'd ...

[PDF]2011 Chevrolet Malibu Owner Manual

https://www.chevrolet.com/.../Chevrolet/.../2011_chevrolet_malib... ChevroletChevrolet Malibu Owner Manual - 2011 ..... remotely lock and unlock the doors from up ... The trunk can only be opened when ...... the vehicle is in motion can be.

Sounds like the body control module is going bad. Need to be sure, not cheap.

Your door lock actuator have issues

I had the same problem with the fuel pressure. I had a brand new fuel pump that was 11 months old. I had that fuel pump replaced. It worked for about 2 weeks and the car would not start. I had to get the security system replaced. The car runs now. I have had this car for three years and it has put me through hell.

well if the radio is locked (like says locked right on the radio) then you can take it to a dealership and have them unlock it for a small fee.... like 5$. they get a code and put it in to unlock it.

look for the lock and unlock relays check them to see if they work.what you do is look at relay.look at terminal blades.you have a number 86 and 85 terminals on relay.connect terminal 86 with a jumper wire to positive battery terminal.then connect 85 terminal to ground with jumper wire.if the relay click its good. if not replace it.if relays is good you have bcm problems it control door locks.dealership job.

check wiring going to door there is a black rubber boot going to door wires have rubbed to a short. roll windows up and down if locks start working thats the door to check If one of your door locks don t work, check wiring

hey check the fues frist. then take a light tester aand see if you have power to your switch. . if every thing work out good it will be the switch

2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.