1994 Dodge Viper Logo

Related Topics:

A
A J VIPER Posted on Jan 30, 2014

I have a 1994 Dodge viper and the gas tank filler has some rust how do I remove and replace the filler tube or can it be cleaned some how

5 Related Answers

Anonymous

  • 335 Answers
  • Posted on Aug 11, 2008

SOURCE: battery location

Behind the Left rear tire behind the bumper under a panel
If you find this information helpful please give me a good rating Please

Ad

Anonymous

  • 1392 Answers
  • Posted on Mar 10, 2009

SOURCE: How to change dodge neon fuel filler neck

unbolt the neck from the body of the car. Drop the gas tank enough to get the neck out. Reinstall.

Anonymous

  • 2 Answers
  • Posted on Sep 11, 2009

SOURCE: 1999 Durango brake line leak

I have just done this job with aftermarket brake lines in three pieces, two 40" and one 30" joined by unions. I did not take the tank down, it is possible to reach the clips holding the brake line from the top reaching in with your fingers from the outside reaching over the frame. Make sure to have good light and a flashlight at hand. Above each clip holding the electric cable run you see next to the tank there is also a slot (in the same clip) for holding the brake line. I used the two long pieces in the rear and slid one in place, then joined it with the second one the short piece I used to do the final bend up to the junction block. The uninon for that one to the other two conveniently ended up right behind the front most clip holding the brake line and the fuel line to the chassis. I am not sure if I saved time or effort doing it this way I just shyed away from bringing down the tank as all I jacked up the car with was drive on ramps and there was not much space under it. Also the brake line did not conveniently burst when I had an almost empty tank to handle but the other way around...

Azrael SRL

  • 11800 Answers
  • Posted on Mar 12, 2010

SOURCE: how to clean rust from motorcycle gas tank

To remove the loose rust fill the tank to 1/4 of its capacity with small pebbles and shake it. To remove the rest fill the tank up to 1/10 with rust converter solution and slowly rotate it to cover all the rusted parts for at least half an hour.

Anonymous

  • 1 Answer
  • Posted on Feb 28, 2011

SOURCE: my 2004 dodge ram 1500 4x4 with a hemi 5.7 will

my 2004 dodge ram 1500 2x2with a hemi 5.7 will not accept fuel.As soon as i start to fill it backs up the filler and stops the pump.the only way i can fill the tank is to hold the fuel nozzel out of the hole ans slowly shoot the fuel into the filler tube.This is not only unsafe for my wife and kids but very time consuming.replaced fuel fill tube already and had breather tube blownout and scoped by a mechanic.He now tells me i need a new $500 gas tank.Is this something i can have the dealership fix for free?

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Fuel filler neck

Hi I'm Peter, Not sure what your problem is from just posting fuel filler neck however I am assuming you have a strong gas smell. The rubber hose that connects the filler pipe on the tank to the fuel spout may be cracked and leaking. Another common problem is the tank vent tube that runs from the tank up along side the filler tube may be rubbing on the metal part of the tube and has a hole in it. This will give you the strong fume smell and possible fuel leak as will the rubber filler tube when the tank is full. These vehicles are known for this problem and also the metal filler pipe rusting causing a pin ole. Look to see if you can see rust anywhere . Even if you don't see rust on the outside does not mean there is not rust on the inside. I have seen where a lot of people have been have the rust issue also to the point they carry the part at auto parts stores . Hope this is what you needed.
0helpful
1answer

How can a gas tank filler tube be repaired on a suzuki esteem?

if you can cut out the bad spot replace it with a piece of radiator hose
0helpful
1answer

How to remove the fuel filler neck on my 1999 Dodge Grand Caravan 3.8 ltr. engine

OPEN GAS CAP FLAP THEN YOU NEED TO DRAIN GAS BELOW FILLER NECK.THEN LOOSEN REMOVE SCREWS IN THE GAS CAP FLAP AREA WHERE FILLER TUBE CONNECTS THEN GO UNDERNEATH VAN LOOSEN REMOVE HOSE CLAMPS AND REMOVE THE HOSE AT THE FILLER NECK BELOW THE GAS TANK.SPRAY WD40 AROUND HOSE AREA AT METAL FILLER TUBE STICK OUT GAS TANK.CAREFULLY USE LARGE PAIR OF CHANNEL LOCK PLIERS TO REMOVE WORK HOSE OFF METAL TUBE FROM GAS TANK. IF YOU CANT REMOVE HOSE WITH HANDS.BECAREFUL NOT TO MAKE ANY SPARKS.PLACE RAGS AROUND ANY METAL PARTS TO KEEP CHANNEL LOCKS FROM HITTING METAL MAKING SPARKS.
1helpful
1answer

Cant fill the truck with gas the pump will shut off and gas can be seen inside the fill pipe. the gas will then slowly go into the tank. the truck is a dodge 1500 hemi 5.7 2x2 .

There is most likely a crimp or blockage in the filler tube. This is the tube that leads between the fill pipe and the tank. You may need to remove the tube and tank or replace the hose so you don't have slow filling problems.
0helpful
1answer

Gas leak from tank when filled and constant smell of gas

The tank's filler tube may be leaking either at a hose clamp connection or metal tube rusted away and has holes.

That's what hapened to my 1990 Cadillac Deville, anyway. Had to replace the filler neck.
0helpful
1answer

How do i take off the gas tank of a dodge caravan

First disconnect the negative wire from battery. Raise the rear othe van and use jackstands to support it. Remove the filler cap and disconnect the filler line to tank. Connect a hose and drain or siphon fuel out of tank into a fuel container. Remove the screws from the filler tube to the van body. Disconnect all wiring and hoses from the tank and mark each to help you remember how to put it back together. Remove the mounting bolts and nuts,lower the tank slightly and remove the filler tube. Lower the tank more and support it while disconnecting the rollover/vapor separator valve hose. Then remove the tank. Installation is the reverse of removal. Be sure to have a fire extinguisher (class b type) to use incase of a fire. Hope this will help you.
1helpful
1answer

How do you replace the gas tank on a 1994 Chevy Lumina Sedan?

disconeccect the filler tube,place a floor jack under the tank,remove strap bolts, lower the tank a little, dicconect the electrictal,
lower the tank alittle more, disconnect the fuel lies,
lower the tank all the way and remove it!!!
put the new one in!!!
0helpful
1answer

When i add gas i have leak in the fill line to the tank, how do i replace it

remove the screws at the top of the filler neck where it attaches under the gas door and then loosen the clamp that holds the filler tube to the tank,and then reverse the instructions to install the new filler tube.
4helpful
1answer

Install a gas tank in a 94 toyota corolla

Raise the car.

Loosen the fuel filler neck rubber hose clamp. Remove hose from tank. Insert tubing into tank and siphon out all fuel.

Undo the brake line bracket blots and move brake lines out of the way.

Undo the exhaust to muffler flange bolts. Exercise extra care if they appear rusted as they will shear off.

Remove rear seat and undo fuel pump cover. Undo fuel pump bolts.
'
Disconnect the fuel and return lines.

Support tank with a jack. Undo tank strap bolts. Remove straps.

Lower tank and remove fuel pump.

Drop tank and slide out over exhaust.





Not finding what you are looking for?

146 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...