Windshield Wiper Motor stopped working.

The windshield wiper motor stopped working and I would like to know where is it located..

5 Related Answers

Anonymous

1 Answer
Posted on Mar 30, 2009

SOURCE: Windshield wiper arm disconnected

My dad helped me solve this problem on my truck...

They simply pry off. He put down a towel to protect the cowl grill, took a hammer (using the split end) and pried them right off.

There was no mechanism holding them on, when we were done working under the grill, we used the same towel, but the other side of the hammer to stick 'em back on.

marionbagget

718 Answers
Posted on May 07, 2009

SOURCE: I have a 1992 dodge shadow.but the windshield wipers isn't working.I checked the motor is well,the terminal voltage is 12V,how can I continu to repair the 1992 dodge shadow's windshield wipers?

You posting is slightly confusing but I gather your windshield wipers stopped working.
The repair method is as follows;
) Check the fuse.
) Check the wiper motor. Turn the wipers on and listen for the hum of the motor.

If you hear the hum then the linkage has probably come loose. You will have to take the covers off
to get to the linkage for the wiper. You can either repair the parts, get salvage yard parts or replace with new part$.

If you do not hear the motor hum then you should verify electricity is getting to the motor. A simple
voltmeter can be used. If the motor is bad you can replace it. Call some auto supply stores for after-market motors or call salvage yards for parts.

Anonymous

353 Answers
Posted on Sep 13, 2009

SOURCE: Where is the windshield wiper motor on a 2007

Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

Testimonial: "Thank you for a clear and concise description of the process."

Jonah Oneal

14092 Answers
Posted on Oct 18, 2009

SOURCE: How to replace the wiper motor in 1997 Caravan?

YOU NEED A REPAIR MANUAL. ALSO YOU WILL HAVE TO REMOVE COWL COVER WIPER WASHER HOSE AND DISCONNECT THE ELECTRICAL CONNECTORS AT WIPER MOTOR..THE WIPER ARMS HAS TO COME OFF.BUT GET A REPAIR MANUAL.IT WILL MAKE YOUR JOB EASY.

Anonymous

2 Answers
Posted on Jan 09, 2010

SOURCE: Windshield wipers don't work but the motor runs . 93 Dodge Dakota

remove wiper arms and then you can raise the hood to remove screws that hold down the vent panel.
now carefully remove vent panel.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

3answers

2004 chevy avalanche windshield wipers only work on high speed , have changed relay on motor and still same problem

The is the symptom of a defective wiper switch.

Read full answer

Nov 07, 2018 • Cars & Trucks

0helpful

1answer

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong

Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

Read full answer

Sep 05, 2017 • Cadillac Cars & Trucks

0helpful

3answers

How do you replace windshield wiper motor on a 1997 ford e250 van

REMOVAL

Raise and support the hood.
Remove the windshield wiper pivot arms.
Remove the cowl top vent panels.

Disconnect the windshield wiper mounting arm and pivot shaft.

Remove the access cover from the dash panel.
Remove the mounting arm and pivot shaft retaining clip.
Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

Remove the windshield wiper motor.

Disconnect the electrical connector.
Remove the three bolts.
Remove the windshield wiper motor.

INSTALLATION

Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

Install the windshield wiper motor.

Place the windshield wiper motor in the dash panel.
Install the three retaining bolts.
Reconnect the electrical connector.

Reconnect the windshield wiper mounting arm and pivot shaft.

Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
Install the access cover in the dash panel.

Install the cowl top vent panels.
Install the windshield wiper pivot arms.
Adjust the windshield wiper pivot arms.

This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Read full answer

Nov 17, 2014 • Cars & Trucks

0helpful

1answer

Replacing wiper linkage

WINDSHIELD WIPERS

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below: -------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Read full answer

Nov 29, 2012 • 2003 Chevrolet Cavalier

0helpful

1answer

Where is fuse for wiper fluid pump on a 2003 cavalier?

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Read full answer

Nov 28, 2012 • 2001 Saturn S-Series

0helpful

1answer

How to remove the windshield cowl on a 2002 tyota yaris

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below:-------

Complete wiper components replacing details ?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

These details will help.

Thanks.

Read full answer

Nov 28, 2012 • Toyota Yaris Cars & Trucks

0helpful

2answers

2002 intrigue wipers / washer dont work

It can be faulty wiper motor or blown wiper control fuse.

Do you hear any kind of noise when you starter the wiper function.If yes then fuse is ok,but issue is wiper motor.
If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring:-----
For complete troubleshooting i suggest you few helpful links with accurate solutions.
-------------
Click the link below:-------

1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html
------------ How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

0helpful

1answer

Wipers don't work on intermittent. They run but stop in they middle of the windshield and don't go to the bottom like normal, Then they run again and stop some other spot. When put on continuous they...

Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper RUN/PARK relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect senses magnet to turn off RUN/PARK sense the output to the windshield wiper RUN/PARK software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.

The intermittent windshield wiper speed does not operate correctly

Multifunction switch.
Circuitry.
Windshield wiper motor.

Go To Pinpoint Test D .

Pinpoint Test D: The Intermittent Windshield Wiper Speed Does Not Operate Correctly
Normal Operation During normal operation, the windshield wiper motor receives voltage at all times through battery junction box (BJB) fuse 1 (30A), circuit 65 (DG). The windshield wiper motor also receives power with the ignition switch in RUN or ACC positions through central junction box (CJB) fuse 33 (15A), circuit 1002 (BK/PK). Ground is provided to the windshield wiper motor through circuit 676 (PK/OG) and circuit 57 (BK). The run/park and high/low relays are contained in the wiper motor electronics. Mode of operation is dependant on the signal(s) received from the multifunction switch.

Possible Causes

Multifunction switch
Open in circuit 57 (BK), 56 (DB/OG), 61 (YE/RD) or 63 (RD)
Windshield wiper motor

PINPOINT TEST D: THE INTERMITTENT WINDSHIELD WIPER SPEED DOES NOT OPERATE CORRECTLY Test Step Result / Action to Take D1 CHECK THE MULTIFUNCTION SWITCH

Key in OFF position.
Disconnect: Multifunction Switch C202b.
Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
Did the multifunction switch pass the component test?

Yes
GO to D2 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . TEST the system for normal operation. D2 CHECK CIRCUIT 57 (BK) FOR OPEN

Measure the resistance between multifunction switch C202b-6, circuit 57 (BK), harness side and ground.
Is the resistance less than 5 ohms?

Yes
GO to D3 .

No
REPAIR the circuit. TEST the system for normal operation. D3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD) AND 63 (RD) FOR OPENS

Disconnect: Windshield Wiper Motor C125.
Using the following table, measure the resistance between multifunction switch C202b harness side and windshield wiper motor C125 harness side:

Multifunction Switch C202b Windshield Wiper Motor C125 Pin 2, circuit 56 (DB/OG) Pin 10, circuit 56 (DB/OG) Pin 4, circuit 61 (YE/RD) Pin 1, circuit 61 (YE/RD) Pin 1, circuit 63 (RD) Pin 9, circuit 63 (RD) Pin 3, circuit 58 (WH) Pin 11, circuit 58 (WH)
Is the resistance less than 5 ohms?

Yes
GO to D4 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. D4 CHECK FOR CORRECT WIPER MOTOR OPERATION

Disconnect all wiper motor connectors.
Check for:
- corrosion.
- pushed-out pins.
Connect all wiper motor connectors and make sure they seat correctly.
Operate the system and verify the concern is still present.
Is the concern still present?

Yes
GO to D5 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. D5 CHECK THE WINDSHIELD WIPER MOTOR

Key in OFF position.
Disconnect: Windshield Wiper Motor C125.
Carry out the windshield wiper motor component test as outlined in this section.
Did the windshield wiper motor pass the component test?

Yes
The system is operating correctly at this time. Concern may have been caused by incorrect binding pivot arm adjustment. REFER to Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

Read full answer

Feb 19, 2018 • 2006 Ford F 350 Super Duty

0helpful

2answers

I have a 2004 chevy cavalier and the wipers do not work at random times. Sometime the wiper will not start at first and stop in the middle and then start working again. I really do not want to get caught...

Could be anything but based on experience the probability points to the self cancelling switching in the motor gearbox.

Read full answer

Dec 18, 2017 • 2004 Chevrolet Cavalier

1helpful

1answer

Need to get a programmer dont know where its at

Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF

Damaged turn signal and windshield wiper switch .
Damaged windshield wiper motor .
Damaged windshield wiper control module.

Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :

Windshield wiper motor (17508) (F-type).
Washer system.
Windshield wiper control module.
Turn signal and windshield wiper switch (13K359).

The windshield wiper control module is:

Located at the instrument panel fuse panel.

The windshield wiper motor is:

Attached to the cowl top extension (021A36) .
Connected to windshield wiper mounting arm and pivot shaft (17566) .

The turn signal and windshield wiper switch features a:

Rotary wiper switch.
Push type washer actuator.

OFF/Low/High Speed

Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
The windshield wiper motor has a brush rigging that permits selection of low or high speed.
When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
When the park switch contacts open, the windshield wiper motor stops in the park position.

Interval
When the turn signal and windshield wiper switch is in the interval position:

The wipers make single wipes separated by pauses.
The rotary switch is on the end of turn signal and windshield wiper switch .
The length of the pause can be set from approximately 1 to 17 seconds.
Length of pause decreases as the rotary switch is rotated away from off.
Length of pause increases as the rotary switch is rotated toward off.

While in the interval wiper mode:

It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

Read full answer

May 27, 2009 • 1994 Ford Mustang

Not finding what you are looking for?

View Most Popular

1995 Stratus

Cars & Trucks

2004 chevy avalanche windshield wipers only work on high speed , have changed relay on motor and still same problem

Cars & Trucks

140 views

Ask a Question

Usually answered in minutes!

Check Out the Latest Top Trucks Report!

View all Fixya Reports

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for 1995 Dodge Stratus? Or just drag it here!

Related Topics:

Windshield Wiper Motor stopped working.

5 Related Answers

Anonymous

marionbagget

Anonymous

Jonah Oneal

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

2004 chevy avalanche windshield wipers only work on high speed , have changed relay on motor and still same problem

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong

How do you replace windshield wiper motor on a 1997 ford e250 van

Replacing wiper linkage

Where is fuse for wiper fluid pump on a 2003 cavalier?

How to remove the windshield cowl on a 2002 tyota yaris

2002 intrigue wipers / washer dont work

1993 Ford F350 wipers not working?

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

Car windshield wiper gets power for movement and stops?

How does cars Windshield Wiper System Works

1997 Honda Protege: Replace Wiper Transmission?

Windshield wiper fluid container leaking?

Where is wiper fuse located on1993 chevrolet suburban

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

Complete wiper components replacing details for Acura Car Models?

Wipers don't work on intermittent. They run but stop in they middle of the windshield and don't go to the bottom like normal, Then they run again and stop some other spot. When put on continuous they...

I have a 2004 chevy cavalier and the wipers do not work at random times. Sometime the wiper will not start at first and stop in the middle and then start working again. I really do not want to get caught...

Need to get a programmer dont know where its at

Not finding what you are looking for?

1995 Stratus

2004 chevy avalanche windshield wipers only work on high speed , have changed relay on motor and still same problem

Ask a Question

Popular Questions

How can I set the timing on a 1996 dodge stratus 2.4l engine

Diagram fuse panel dodge stratus 2005

2005 Dodge Stratus ? Camshaft Position Sensor causing problems (I

Transmission faul code po700

How do i disable the anti theft system on a 04 dodge stratus

Check Out the Latest Top Trucks Report!

Top Dodge Experts

ZJ Limited

Thomas Perkins

Arnie Burke

Are you a Dodge Expert? Answer questions, earn points and help others

Manuals & User Guides