Question about 1998 Chevrolet C2500

Open Question

I need torque specs on asia wing 3 ton truck

Head torque settings

Posted by 4alladmin on

Ad

5 Related Answers

ITGuy181

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

Ad

Anonymous

  • 17 Answers

SOURCE: I need the torque specs and sequence on a 1998 chevy 350 vortec

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

Posted on Apr 25, 2009

Ad

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

wilsodfarm

Donnie Wilson

  • 986 Answers

SOURCE: Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?

.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Posted on Mar 16, 2010

Anonymous

  • 75 Answers

SOURCE: TORQUE SPECS /HEAD GASKET/2001 CAVALIER...

for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Posted on May 24, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

1 Answer

Torque settings on a fiat uno 1100 engine


Answer barbo(fiat mechanic) Fiat do not issue torque settings for a punto they use angles so that you can snap your stretch bolts! after contacting fiat and haynes neither of them would give proper torque settings, so i delved into my many tech manuals on fiat fire engines which is what is in your punto and i have successfully changed many fiat punto head gaskets using the following torque settings: stage 1 starting from the centre head bolts tighten to 33nm: stage 2:65nm and finally stage 3: 96nm these torque settings work fine and will probably save you buying new head bolts.

Oct 29, 2014 | Cars & Trucks

1 Answer

I need torque settings for engine 15B/F 4104cc


Check out the help links mentioned below:----
Cylinder Head Torque Setting http://schematicsdiagram.blogspot.com/2012/10/cylinder-head-torque-setting.html
----------- Lexus LS400: Transmission or Torque Converter? http://technoanswers.blogspot.in/2012/04/lexus-ls400-transmission-or-torque.html

----------
For more help.keep updated.
Thanks.

Oct 15, 2012 | Toyota Cars & Trucks

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

1 Answer

Hi can you tell me the torque setting for the cylinder head on a 1995 C200 Mercedes W202 series Thanks Ken


if this is a aluminum head it will be a torque to yeild. you will need brand new head bolts and a torque to yeild wrench, torque to yeild is not a set value but the stretching point of the bolt, wich a torque to yeild wrench will tell you when the bolt is starting to stretch then you stop and torque is achieved. often the starting torque is approx 30pds then you go back through with the torque to yeild wrench. if it has a cast iron head it will have a set value determined by the manufacture which on this car i do not know off hand. I hope i at least led you in the right direction

Mar 18, 2010 | 1995 Mercedes-Benz C-Class

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

4 Answers

Torque wrench settings


please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
1998 Chevrolet C2500 Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...