Centre consol can,t find screw to remove consol

There will be small plastic covers on the sides of the centre console concealing screws and under the cup holders and at the bottom of the centre console. Gently pull up on dash trims to unclip them

This can be one of those jobs that isn't hard but it's a pain in the backside! I would suggest chocking the wheels and use the handbrake as you may need to take it out of Park to do it. The leather Gaiter is fitted as part of the centre console.
Lift the lid on the centre store box, (where your elbow rests when your driving). On the top edge, level with the latch there should be access to a screw pointing down to the floor. Remove it. The centre panel, (with the cup holders in it), should lift up, screw end first. You might need to put the vehicle in Drive to get enough clearance. This should give you enough access to the underside of the gaiter. There is a small screw holding the shifter grip in place. Remove it and the gaiter and centre console should lift off. The shifter grip might be tight but should 'wriggle' off.
The gaiter should be easier to remove once all this is done.

Lift up gearstick gaitor leaving plastic surrounding in place.

Lift plastic surround and remove lock and Hazzard switch.
Push gaitor through surround and remove surround.
Remove ***** from front of centre consoleand 2 screws from rear.
Follow the side of the centre console down into footwell and remove Popper from each side.
Pull console forward slightly and disconnect cigar lighter.
Remove centre console.
Remove 2 screws below the radio.
Pull radio/air-conditioning surround forward, leave the radio in the surround as it will come out with the surround.
Remove 2 screws holding the glovebox to the centre console.
Open glovebox.
Remove 3 screws along the top front.
Open the fuse box at back of glove box and push the fuse holder up off the flap.
Open passenger door.
Remove dash side panel and remove 2 screws.
Remove kick panel trim in passenger footwell and remove ***** from bottom of glove box. (The glovebox will need to be open to see this *****)
Pull glovebox out slightly. It can be hard to pull out, just be sure you have all screws out.
Disconnect glovebox light and light switch.
Remove glovebox fully.

remove plastic gearchange cover four clips use small plastic blade down each side about 20mm from each end to release, disconnect switch connectors.remove 4 screws and metal retainers, may have spacing washers underneath.remove veneer j gate surround.remove rear centre console end held by clips just pry off carefully,remove 4 torx screws now exposed. remove centre console you may have to disconnect electrical connectors depending on vehicle spec.cig lighter on all,it will then enable the audio unit fixings to be removed make sure you remove the gearshift from P and disconnect battery before you start work

disconnect battery. remove 1 gearshift surround held by clips. 2 centre glove box liner, 3 rear console air vent. 4 centre console held by screws. audio stack held by small bolts. make sure you remove gearshift from P before you disconnect battery,

for center console removal start furthest point from dash move seats forward and look for screws of either side of console. may also be in storage area of console. remove back section first which will reveal screws for front which should reveal screws for area that holds cig lighter and such

Hi, really easy if you know how! Use a curved piece of wire to hook in and behind the eyeball (I bend one into a tight U shape push in and pull back) grasp wire tightly and pull hard. It feels as though they will break but they wont, they're held in with clips behind the fascia.The Centre console is held with clips also and two screws either side of the gear knob on the sides. When the screws are removed, pull hard again to remove the console. Good luck!

Remove the twi phllips screws under the cup holders. Remove the cover in back of the arm rest. Remove the two phillips screw. Remove the cap covering the last screw in the back of the console. Remove last phillips screw. pull up parking brake,remove console. Good luck.

You'll need to remove the entire vertical console (pops out after you remove two phillips screws at the bottom behind the cup holders). There are two phillips head screws (possibly 4) holding the digital clock in place (back side) of the vertical console.

remove the draw.. there should be 2 screws visible now. take them out and then pry the rest loose. Dont break the clips !!!!!