Question about 1999 Daewoo Lanos

1 Answer

Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

Posted by lewiswycham on

  • Anonymous Mar 17, 2014

    How do i change the oil myself in a 2000 model daewoo lanos (3 door hatchback, auto).

×

Ad

1 Answer

Marvin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 85,239 Answers

Here is the entire timing belt replacement procedure.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 22, 2009

Ad

1 Related Answer

stevenhurc

Steve Hurc

  • 459 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

single cam or twin?

466b3f3.jpg 1f27bcc.jpg

Posted on May 28, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where should timeing marks be set on 2000 daewoo lanos


there should an underhood sticker with that specification, it's with spark plug gap

Jul 04, 2010 | 2000 Daewoo Lanos

1 Answer

Engine timing belt 1600 daewoo lanos


It connects the crankshaft to the camshaft, which controls the valves that let the air fuel mix in and the exhaust out of the cylinders

Apr 14, 2010 | 2000 Daewoo Lanos

1 Answer

Timing belt marks 2001 lanos 1.6 liter


The camshaft sprockets have an indention on them you will align them to the inside horizontally so they are side by side. The crankshaft sproket also has a timing mark on it and you will align that with the timing mark on the rear timing belt cover vertically. The tensioner aligns with with the notch on the automatic tensioner bracket. Hope this helps you.

Nov 29, 2009 | 2001 Daewoo Lanos

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

1 Answer

Locating camshaft positioning sensor on 2000 Daewoo Laganza


hi,
it is under the upper timing belt cover between the camshaft gears. According to the manual touching anything related to timing belt requires removing million parts including right front wheel. I suspect this might be an overkill just to remove upper timing belt cover.

So my advice would be to get it done by some mechanic as u will not be able to do it and may damage other parts also.

Thanks!
Sandy

May 18, 2009 | 2000 Daewoo Lanos

1 Answer

Locating camshaft positioning sensor on 2000 Daewoo Laganza


when you open your hood and you look on the valve cover you see on your left side of top of your cover a cable sticking out from a black piece that is the positioning sensor that cranksup the car

Mar 03, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
1999 Daewoo Lanos Logo

533 views

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

john h

Level 3 Expert

23915 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14869 Answers

xxxxxx xxx

Level 3 Expert

5023 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...