Question about 1997 Ford Expedition

1 Answer

1997 F150 4.6l cruise control does not work.where do i start?

Posted by bandc307 on

  • Marvin
    Marvin May 11, 2010

    u start by testing the cruise control activation switch in the horn pad.

×

Ad

1 Answer

Sergio Sosa

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 25 Answers

Does Ford replaced the cruise control deactivation switch.
Vehicles involved in the recall include the following:

1998-2002 Ford Ranger
1992-1997 Lincoln Town Car
1992-1997 Ford Crown Victoria
1992-1997 Mercury Grand Marquis
1993-1998 Lincoln Mark VIII
1993-1995 Taurus SHO
1999-2001 Ford Explorer
1999-2001 Mercury Mountaineer
2001-2002 Ford Explorer Sport
2001-2002 Ford Explorer Sport Trac
1992-1993 E150-350 Vans
1997-2002 E150-350 vans
1993-1997 Ford F-Series pickups
1993 Ford Bronco
1994 Mercury Capri
2003-2004 Ford F0150 Lightning
1995-2002 Ford F53 motor homes.

Posted on May 15, 2009

Ad

5 Related Answers

s60six

  • 328 Answers

SOURCE: cruise control wont work

normally the brake switch is the issue with these trucks. it is located under the dash where the brake pedal meets the linkage to the brake booster.

Posted on Feb 16, 2009

Ad
sscullys

Steve S

  • 984 Answers

SOURCE: 2002 Ford F150. Cruise control stopped working.

Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Posted on Feb 23, 2010

Anonymous

  • 3 Answers

SOURCE: I have a 2002 Ford F150. Fuse 15 (5 Amp) keeps blowing.

replace nuetral safty switch for gear shifter and check window relays

Posted on Feb 12, 2010

Anonymous

  • 31 Answers

SOURCE: 1997 plymouth grand voyager cruise control problems

Try doing a "Brain Kill" on the van. Disconnect both battery terminals, and (MAKE SURE THEY ARE NOT CONNECTED TO THE BATTERY!!!!!) touch and hold them together for at least 10 seconds. Mopars hold onto their faults, even after the repairs. Huge problem for transmission shops, but that's another topic. My 99 Dakota had the Speed Sensor fail, and it wouldn't shift until I "Killed" the ECM and BCM's memories.

Good Luck!!!

Posted on May 22, 2010

Anonymous

  • 32 Answers

SOURCE: 1997 F150 HORN,CRUISE CONTROL,RADIO NOT WORKING

probally a fuse has blown. Check fuse box under steering wheel by pedals and the fuse box under the hood. should be on drv sd inner fender

Posted on Feb 28, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cruise control is not working....is that a fuse problem....also does a light come on when low on gas?


The cruise control light blinks when there is a problem with it.

Here's a link for a kit that repairs the Subaru 1997-1998 Cruise control system if not working:
http://www.mnrelectronics.com/sucrco1.html

Aug 02, 2010 | 1997 Subaru Impreza

1 Answer

Hey got a cruise control problem


a mechanic just replaced a vacuum hose (don't know where) and my cruise control started working again!

Oct 07, 2009 | 1997 Dodge Grand Caravan

3 Answers

Cruise Control Not Working, Fuse OK, where do I go next?


my 1997 honda accord cruise control fuse blow and the car start up but will not go in gear. I change the cruise control fuse the car goes in gear then the fuse blow again. WHAT IS THE MY CAR PROBLEM.

Oct 01, 2008 | 1997 Honda Accord

6 Answers

1997 Dodge Ram 2500 Cummins Turbo Diesel


The cruise control on y 1997 dodge cummins diesel 4x4 suddenly stopped working.I checked the fuses but they are ok.any solutions?

Jul 12, 2008 | 1997 Dodge Ram 2500 Club Cab

Not finding what you are looking for?
1997 Ford Expedition Logo

2,576 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...