Question about Cars & Trucks

Open Question

Torque settings i urgently need torque settings for Chery QQ(0,8 TE)...I need main bearings settings,big end bearings settings,flywheel settings,and cylinder head settings.

Posted by Anonymous on

Ad

5 Related Answers

Stanley Kramer

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

Ad

mdcliff

  • 360 Answers

SOURCE: I WANT TO HAVE CYLINDER HEAD TIGHTENING TORQUE AND

Go to a auto parts store (Pep Boys, Auto Zone, Advance, O'Reilly's, etc. ...they all have vehicle specific manuals for sale that will have a section on torque values.

Posted on Dec 26, 2010

Ad

Anonymous

  • 9 Answers

SOURCE: main bearings and big end bearings tension specs

This site has all the torque specs you should need make sure this is the correct engine.

http://www.davidfarmerstuff.com/C6Z06-Torque.pdf

Posted on Dec 27, 2010

Jonah Oneal

  • 14092 Answers

SOURCE: Saab 95 Aero 2.3 turbo. I need torque settings

CYLINDER HEAD BOATS TORQUE FIRST PASS 29.5 FT LBS SECOND PASS 44 FT LBS.THEN TIGHTEN ADDITIONAL 90 DEGREES FOR MAIN BEARINGS 15 FT LBS TIGHTEN EACH BOAT ADDITIONAL 70 DEGREES ROD BEARINGS 15 FT LB TIGHTEN ADDITIONAL 70 DEGREES. CRANKSHAFT DAMPER BOLTS 130 FT LBS.

Posted on Jan 26, 2011

turbot551

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All torque settings on a 4af toyota


cylinder head bolts
stage1-20NM
stage2-40NM
stage3-60NM

MAIN BEARINGS
stage1-30NM
stage2-60NM

BIG END BEARINGS
stage1-25NM
stage2-49NM

FLYWHEEL
78NM

Sep 05, 2016 | Toyota Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Looking for cylinder head, main bearings, big end bearings and flywheel torque settings. Also valve clearence for same engine.


go google and type in - torque settings for (your engine as you haven't given that infomation) and there will be pages of details
There is no flywheel for an automatic. What you have is a flex plate as the torque converter acts as a flywheel

Mar 18, 2015 | Cars & Trucks

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

3 Answers

I need to kno the cylender head torque specs for a 2.3i vw microbus five cylender


The Audi 5 cylinder engine (Engine code AFU) was mainly produced in South Africa and was called a Microbus. The engine capacity was 2309cc. The Microbus 2.3i T3 was produced from 1992-2002.

According to Mead & McGrouther - Data Digest the torque settings for the cylinder head bolts are as follows: 40Nm + 60Nm + 90'degree turn + 90' degree turn. The cylinder head bolts has to be replaced with brand new ones.

The Main Bearings: 65Nm. The Big Ends: 30Nm + 90 degree turn.

The OHC Bearing Caps: 20Nm.

Flywheel Bolts Manual transmission: 60Nm + 90 degree turn.

Jul 28, 2014 | Cars & Trucks

1 Answer

Torque settings for Nissan na 20 cylinder head


I need the torgue settings for Nissan Hardbody NA20 engine
: Mains bearings, Big ends and flywheel as well as timing belt settings

Feb 11, 2013 | Cars & Trucks

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...