Remove broken antenna

Power Antenna Mast Replacement 97 fjz-80 ' IH8MUD Forum

forum.ih8mud.com > Forums > Toyota Tech Forums > 80-Series Tech

Oct 1, 2010 - I'm looking for a "how to" on replacing the OEM power mast on a 97 LC. ... The only tricky part is removing the funky nut that holds the mast in. .... what to do with the radio mast on my newly acquired 1997 Lexus LX450. ... if I have a broken cable, but the antenna itself comes right out of the top with no cable.

How to rebuild the power antenna - Cadillac Forums

www.cadillacforums.com > ... > Cadillac Tech Tips - How to fix it

May 9, 2009 - 15 posts - ‎12 authors
Remove the liner to access the antenna and disconnect ANY of the two ... If notlocked the motor receives continuously power and will drain ... Broken nylon wire lifting/lowering the antenna mast 4. ... The motor shaft comes out from the plastic casing after you take out ... Do not lubricate the cable or the mast.

Saabnet.comt Broken Antenna FAQ - The Saab Network

www.saabnet.com/tsn/faq/antenna.html

If the cable broke in the antenna, you need to remove the antenna to remove the ... take a 17 mm wrench and remove the nut over the antenna where the mast comes out of the body. ... Hopefully the chrome sleeve will come with the old mast. ... Be careful not to drop them down too far. get the motor assembly on a bench ...Missing: tacoma ‎1997

How To Repair A Broken Car Antenna -EricTheCarGuy ...

? 20:53
https://www.youtube.com/watch?v=zcKwFto9_s0
May 24, 2013 - Uploaded by EricTheCarGuy
This video shows one way you can deal with a broken antenna. ... Find out why ... this video is that I did ...Missing: chrome

Three that I have run onto. One unscrews from the bottom, one,the chrome part on top unscrews, The third, pop off the plastic cap on top and it has a set screw to remove.

Is this a power unit?

Owner's manuals do not show how to repair your car.
Even some factory service manuals ( costing $ 25 - $ 100+) do not list all the steps and tools and procedures to fix this.
Most antenna's are fastened inside the fender or roof panel or wherever you see them.
It can take a lot of work to change one.
Sometimes it takes a garage or body shop a few hours of labor to do this, depending on what must be removed to access the holding device.
Be blessed.

Try and clean the entire motor and antenna setup.

There should be a ring with a couple of notches in it at the base of where the antenna use to be. This ring is essentially a nut and is threaded and can be easily removed giving you better access to the broken antenna. I'm assuming that you are referring to a power antenna also.

Give these instructions a shot. Might be too generic but might be enough to get you going. Removing Original Antenna
1. Step 1 Activate the antenna switch to the up position.
   
2. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
   
3. Step 3 Gain access to the underside of the area where the antenna is located.
   
4. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.
   
5. Step 5 Remove the mast.
   
6. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
   
7. Step 7 Remove the ground lead from the panel.
   
8. Step 8 Pull out the antenna coaxial cable.
   
9. Step 9 Unplug the coaxial from the extension coaxial cable.
   
10. Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.
    Installing the New Power Antenna
11. Step 1 Inspect the fender area where the antenna mast will be mounted for rust.
    
12. Step 2 Clean the area before installing the new antenna.
    
13. Step 3 Plug the new antenna coaxial cable to the extension coaxial cable. (On some General Motors and Ford cars you may need an adapter to mate the 2 cables together. Car audio retail stores sell such an adapter.)
    
14. Step 4 Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
    
15. Step 5 Connect the power lead of the antenna to the power antenna lead on the radio.
    
16. Step 6 Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
    
17. Step 7 Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
    
18. Step 8 Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
    
19. Step 9 Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
    
20. Step 10 Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
    
21. Step 11 Stop the motor after the cable goes into the housing 12 to 25 inches.
    
22. Step 12 Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
    
23. Step 13 Replace the retainer nut to the base of the antenna mast and secure tightly.
    
24. Step 14 Replace the panel that covers the antenna mount area.
    

it unsrews


Antenna Base Removal

1. Remove the antenna mast from the base.

unscrw counterclocwise

1. Detach the interior light.

1. Remove the interior lamp.
   • Disconnect the interior light electrical connector.

1. Remove the interior lamp bezel.

1. Remove the antenna cable/base retaining screw.

1. Remove the antenna base.

The antenna is run up and down by a geared nylon cable, your is broken, many times the cable can be replaced, which is much cheaper than the antenna assy. Check with the local dealer for the cable kit, but unless you are really mech. inclined I would either let the dealer do the job, or a good local mechanic you trust.