Question about 2002 GMC Safari

1 Answer

Cost engine valve replacement - 2002 GMC Safari

Posted by Paul Autio on


1 Answer

Craig Lovick

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 247 Answers

Could cost between $1400-$1800

Posted on Nov 04, 2013


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What is a cylinder compression how much do it cost to replace it

If you have low (or no) compression in one or more cylinders, it can be due to broken/bent valves or valve seats, bad or broken piston rings, or mechanical timing way off. The cost to correct is very dependent on the specific cause. Best case is mechanical timing is way off (this will show up as low/no compression in all cylinders), assuming no other mechanical damage was done. Worst case is engine rebuild or replacement.

Aug 22, 2017 | Cars & Trucks

1 Answer

Leaking valve seals. I want to know the cost to replace versus trading in the vehicle. The vehicle has 176000 miles and is in perfect condition. In fact, the original brakes still have 2/3 of the pads...

The valve stem seals can be replaced without removing the cylinder head(s) using special tools, so the cost would be be around $600.00 for the V6 engine and about $350.00 for the 4 cylinder engine. Since you don't mention which engine you have I provided both estimates. Keep in mind the parts to do this are the least amount of the cost (about $30), the major cost is labor, labor rates vary wildly from state to state even city to city, so get multiple estimates, Any well trained technican and well equipped repair shop can do this basic repair. If the new seals don't correct the problem which I assume is smoke then the engine has other much more expensive problems like worn piston rings and worn valve stem guides.

Oct 13, 2011 | 1990 Toyota Camry

2 Answers

My tensioner broke in my 2004 Honda Civic. The dealer replaced the tensioner and pulley but says there's still no compression. So they say it seems the valves are damaged. So the next stage would be to...


Jun 22, 2011 | 2003 Honda Civic

1 Answer

What are the most common problems with this vehicle.

According to

Occasional problems on this vehicle are plugging of the Exhaust Gas Recirculation (EGR) Valve Passages (2.4L engine only) and failure of the Fuel Pump Sending Unit Assembly Connector Terminals. Plugged EGR Valve Passages may cause the engine to misfire and may also cause the Check Engine Light to illuminate. Failure of the Fuel Pump Sending Unit Assembly Connector Terminals can cause loss of power to the fuel pump leading to a crank and no start or an engine stall while driving. A periodic problem on this vehicle is failure of Distributor Assembly (3.3L only). The cost to repair the EGR Valve Passages is estimated at $10.00 for parts and $130.00 for labor. The cost to replace the Fuel Pump Sending Unit Assembly is estimated at $206.41 for parts and $195.00 for labor. The cost to replace the Distributor Assembly is estimated at $370.00 for parts and $39.00 for labor .All prices are estimates based on $65.00 per flat rate hour and do not include diagnostic time or any applicable sales tax.

Mar 09, 2011 | 2001 Nissan Xterra

1 Answer

MY Truck will not start. Mechanic said it was a timing belt issue. I would like to know what is, in summary, the cost of this. He's trying to charge me a arm and a leg

The timing belt connects the main crank at the bottom of the engine to the camshaft and other bits and bobs at the top of the engine.

The crankshaft lifts and drops the valves in the top of each cylinder to allow fuel in and exhaust out at the correct moment in the engine firing cycle.

If the timing belt fails while the engine is running, the crank keeps turning pushing the pistons up and down while the valves remain still. invariably, the pistons travel up and hit open valves, causing all kinds of cylinder head and valve damage.

The repair usually entails, the removal, rebuild and replacement of the cylinder head. Assuming the cylinder head can be rebuilt. It may be cheaper, taking labour costs into account to replace the whole engine with a second hand/refurb.

Mar 08, 2011 | 2003 Pontiac Aztek

2 Answers

2000 Windstar 3.8L,, If the timing belt goes, is it no clearance between the valves and pistons?

No there is no clearance, so you will bend your valves which will cost you much more to replace than a $20 timing belt plus labor.

Jan 24, 2011 | 2000 Ford Windstar

1 Answer

V.w.jetta gas eng. timing belt broke ? .shut engine off then wood not start . dealer says needs head work ? bent valves? without disasembling is it possible valves never came into contact with pistons ?

Hi, im afraid i can only give you bad news im afraid, if the engine was running even on tick over when the belt snapped then this would have caused the valves to smash into the pistons as the top half of engine would have stopped spinning leaving at least 2 valves in the out position but what causes the damage is the bottom half of the engine, as their is no weight on the cams to keep them turning they stop at once but the bottom half the crank has a big weight called the fly wheel now when the belt snapped the cams would have stopped dead but the crank would have carried on turning under its own weight and this is what causes the piston or pistons to hit the valves this then causes the valves to bend and all the valves will need replacing and the whole top end rebuilding with new seals and the new valves and valve seats will need grinding in.

how ever as its only usually the top half that gets damaged you could save yourself some time and money by calling a local breakers yard and see if they have a cylinder head lying around or even a whole engine as the cost of rebuilding you head and engine would cost more than it would to get a second hand cylinder head or if you didnt want to take any chances look into getting a whole engine.

look at the costs involved get a quote off you garage for the head rebuilt and new valves, tell them worse case if it needed complete head rebuild with all new valves and valve seats and all the seals get a price on the whole job then ask them how much it would cost if you supplied a working cylinder head or even whole engine then compare the prices and check with some breakers for cylinder head prices or engine and you should find that a second hand head will work out cheaper than having yours stripped and rebuilt with new parts.

let me know how you get on or if you need further assistance ok

please rate this solution as i have a whole page of unrated posts, thanks

Nov 22, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

How much should it cost to replace a bad egr valve for a 2005 chrysler 300c

An EGR valve is simple enough to replace. The part alone costs roughly $90.
It is located at the back of the engine.
If you take a look, there will be a Iron rod going from the back of your intake manifold ... downwards ... its going to the EGR Valve.


Aug 24, 2010 | 2005 Chrysler 300

4 Answers

Timing belt broke i just readed that when the timing belt break on this car u have to replace the head cylinder coz the valve are bent is this true its 2000 daewoo laganza

True, the engines are low tolerance engines which means that there is no room for the pistons and valves in the cylinder walls at the same time. When the pistons are TDC and the valves are open, they will hit causing damage to the valves and pistons.
Be more cost efficient to replace the whole engine, rather then just the valve train redone. Chances are the the pistons will have some type of damage and it will not just be one piston that will need to be replaced.
Thank you for using Fixya and sorry for the bad news

Apr 01, 2010 | 2000 Daewoo Leganza

2 Answers

Bent valves 2000 Ford Escort ZX2

a couple bent valves shouldnt be more then a few hundred dollars to have replacedand can be fixed yes, but also the vehicle has to have another timing chain ooput on and be retimed this will probably be a total cost of somewhere in the $800 dollar range (this is only an estimate!!) to replace your entire engine would cost substantially more and in all realit i would try to sell the opother vehicle for parts, trade in, or as a whole and buy another vehicle before i invested the money into a new engine for this particular car

Sep 05, 2009 | 2000 Ford Escort

Not finding what you are looking for?
2002 GMC Safari Logo

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1255 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides