2003 BMW 325 Logo

Related Topics:

p
patterson koster Posted on Oct 27, 2013

My bmw 320i e46 manual is giving me problems.Every time l get to a stop sign or robot my car stalls and then cuts off

1 Answer

Brian Collison

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 11 Answers
  • Posted on Oct 28, 2013
Brian Collison
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

Joined: Oct 28, 2013
Answers
11
Questions
1
Helped
3148
Points
14

More detail needed. Is the clutch dragging causing the engine to stall?
Does it otherwise idle OK?
Any fault codes?

3 Related Answers

motor1258

Mike Butler

  • 6674 Answers
  • Posted on Jun 04, 2009

SOURCE: a battery sign appears in my car gage for BMW

Check & clean all battery connections first, see if that helps, then if not, Have your battery & charging system checked, such as alternator. It's trying to tell you somethings not right.

Ad

Anonymous

  • 243 Answers
  • Posted on Oct 31, 2008

SOURCE: BMW 320i year2002 e46

I don't think your trouble is on the ignition side of it but I am sure that you must have a look at the idle speed control(stepper motor).
If with temperatuer your "misfire"changes to better, it means that it's probably running too lean at cold, normally the stepper motor or ISC does this job.
Let us know how you get on.
Cheers.

Anonymous

  • 83 Answers
  • Posted on Mar 18, 2011

SOURCE: I have a Semi-Automatic 2005

The problem you are having sounds suspiciously like the torque converter is not disengaging to allow your engine to spin freely until you are ready to accelerate.If when decelerating or coming to a stop you feel a jerking sensation similar to driving a vehicle with a manual transmission and bringing the vehicle to a stop without depressing the clutch, then the problem you are having is faulty Torque Converter Control Solenoid or a bad Torque Converter itself. If you have any other questions please contact me here. Good luck.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 BMW 325i. My turn signals, fog lights, and dash light don't work.

Question edited for clarity.
Question moved to model category.

AI Answer Bot answer deleted.

Check the fuses.

BMW 3 Series E46 Fuses and Relay Diagrams

bmwguide.net https://bmwguide.net > 3 Series > E46

Jan 17, 2023 - The main fuse box is located in the glove compartment. You will see two white latches (left and right) that need to be turned to open the fuse ...

Fuse and relay box diagram BMW 3 E46

fusesdiagram.com https://fusesdiagram.com > BMW

Fuse box diagram BMW 3 E46 ; 6. Reversing lamp/s relay ; F1. (30A) Ignition coils-320i with MS43/325i/330i ; F2. (30A) Engine control module (ECM), reversing lamp/ ...

..
0helpful
1answer

BMW 320i E90 when I drive more than 50Km and press a brake pedal at a stop sign or robot the light for low oil pressure shows but when I release the brake it goes what can be the problem?

If this light comes on you need to check oil levels and top up if necessary. If the light still does not go out, chances are you need to replace the oil level sensor.
0helpful
1answer

What type of engine oil for a 320i bmw e46

Use a good synthetic oil 5W30 or 5W40 or 0W40. I think you have to use the bmw long life oil rating.
0helpful
1answer

L have a 2000 BMW 320i e46 which started giving me problems this morning.Every time l get to a stop sign or a robot my car is stalling and then cuts off.

General advice:
Radio interference.
Ceck alternator recharge rate.
Very low on details,u mean if in a parking lot it will iddle fine?If breaking hard won't stall?If easy break engage won't cut?
Fuel/Fuel line/fuel pump related issues.
Air mass (MAF) sensor related.
U must track the problem,more details.
Cheers,share if figured out.
0helpful
1answer

Bmw 320i E46 I have a problem,that when my car is off,the yellow engine light is on,but when i turn my car on,the light dissappears?What do i have to do?

You must get the electronic engine control module scanned, when this light is turned on a fault code is stored in the control modules memory.
3helpful
2answers

I have a Semi-Automatic 2005 BMW e46 318i. The engine randomly cuts out (stalls) when decellerating, coming to a stop, or when stopped. Other than this problem the car drives fine, and the engine starts up...

The problem you are having sounds suspiciously like the torque converter is not disengaging to allow your engine to spin freely until you are ready to accelerate.If when decelerating or coming to a stop you feel a jerking sensation similar to driving a vehicle with a manual transmission and bringing the vehicle to a stop without depressing the clutch, then the problem you are having is faulty Torque Converter Control Solenoid or a bad Torque Converter itself. If you have any other questions please contact me here. Good luck.
1helpful
2answers

Can you provide a diagram of the engine layout for BMW 320i, E46 diesel engine type M47. Its a 2001

hi try this site
www.realoem.co.uk
you will find everything on there you will need for your BMW...hope this helps
0helpful
1answer

A battery sign appears in my car gage for BMW

Check & clean all battery connections first, see if that helps, then if not, Have your battery & charging system checked, such as alternator. It's trying to tell you somethings not right.
Not finding what you are looking for?

307 views

Ask a Question

Usually answered in minutes!

Top BMW Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

old marine
old marine

Level 3 Expert

2426 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...