Question about 2002 Chrysler PT Cruiser

1 Answer

I have no lights inside or out. I replaced wiring but still don't have lights

Posted by Viola Welch on

Ad

1 Answer

bjg8

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 174 Answers

General advice:Main fuse /relay under the hood.What do u mean by replacing the wiring,it is a complexe hell of a messy job everything can go wrong.U must track the problem,ceck bulbs,ceck plugs,ceck switches,ceck fuses in the fuses box.Tip:some lights may not work without the keys on the on position.Very rare is a ignition barrel condition by not letting the + to get to the main fuses panel.Cheers,let others know if u figured it out.

Posted on Oct 26, 2013

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 78 Dodge D150. I get in it dome light is on. I turn the key on and everything goes dead I mean everything headlights don't even turn on. I have a new battery on it. I know I have a short I...


You either have a corroded battery terminal, or corrosion at the positive terminal. Using just a simple 12v test light, put one probe on the neg terminal, then probe the positive terminal. Then probe through the insulation directly into the cable wire about an inch away from the terminal. (battery acid fumes will creep between the wire and the terminal, causing lead oxide INSIDE the terminal. If that's what you find, cut off the terminal and replace it. You can get solder on terminals, which is what you should use, not the "clamp on with a strap and 2 bolts type"

Dec 14, 2017 | Cars & Trucks

1 Answer

Head lights, tail lights and dash lights don't work. inside lights, brake lights, and back up lights do work.


need so check ground wires. start at your head lights and fallow the wire harness til you see a wire grounded to the body. check and make sure connections are good and that the wire isnt broken anywhere

Mar 23, 2013 | 1994 Dodge Caravan

2 Answers

HOW TO REPLACE HIGH MOUNT BRAKE LIGHT 2002 CADILLAC DEVILLE


The light will be fitted from inside the trunk. You might need to remove any trim or lining on the trunk lid. There will be 5 small nuts on the inside of the trunk lid. 2 each end and one centre. The light should drop out. It could be tight so GENTLY rock it up and down to free it.
** NOTE ** The light fitting is likely to be a sealed unit so you will have to replace the whole light as you cant get access to the bulbs.

Mar 01, 2018 | Cars & Trucks

1 Answer

Don't have signal lights and heater blower inside of vehicle want work


It looks like it's possible something regarding your battery wasn't hooked up correctly after your heater control valve was replaced (a wire could have just been jarred loose) which would cause the radio/lights not to work. Your best bet is to contact the mechanic to get it fixed.-------------------------------------------------------------------------------
Programmateur De Calculateur

Dec 07, 2012 | 1994 Ford Explorer Limited

1 Answer

My 1997 Mazda Protege heater does not blow air, i replaced and tested blower motor, resistor and fuses inside the cab. Still nothing


Before replacing the blower motor, you should have checked the motor's input wiring loom for power.
Do you have power here?

If you don't have power, then you need to check your blower switch output wires.

Nov 04, 2012 | 1997 Mazda Protege

1 Answer

The lights behind the radio controls don't work. Not sure if it is a fuse or light bulb problem.


There is a tiny bulb inside the radio that has burned out, the radio must be removed and the light replaced, this is best left to a radio repair shop as the common practice on new radios is to have the bulb hard wired into the circuit board at the front display.

Sep 13, 2012 | 2006 Honda Civic 1.8

1 Answer

Cant get power anywhere on 1992 chevy 2500 pickup no lights nothing has brand new battery


Check your ground cable. It should go to the motor and two the chassi (bolted to a fender).

Look for fuseable links. They always seem to move. They are about a 10 gauge sized wire with a plastic collor on it near the end. There can be some coming off the battery cable at the starter, on a junction block mounted on the firewall (If I remember right your 92 will have a cover on the passenger side firewall and I think they are under that) or near the battery.

Don't just look at the links (the fuse is actually the wire. It melts away when there is a circuit problem), tug a bit on them. They will corrode on the inside of the plastic collor and the wire may not be melted away but the connection inside can be bad.
If a link is bad, DO NOT REPLACE WITH A REGULAR FUSE. I seen people do that and a fuse, like found in the interior fuse panel, creates a resistance. You don't want to turn a 10 gauge wire into a small wire like found in a fuse. Napa auto parts has fuseable link wire. A but splicer and a ring splice would also be needed.

If the links are good then you need to check the bulk head connector on the drivers side firewall. The battery power will go through that inside the vehicle.

Sep 30, 2011 | Cars & Trucks

1 Answer

There is no power to my injectors changed the computer and ignition chip inside.....node lights do not light up


It could be one of two things a bad glow plug controler located at the back of the engine by fire wall, or

a bad temperature switch. it is located at the front on the intake manifold. check for voltage at the glow

plug controller with a test light if you have voltage and voltage going to the glow plugs, its the

termperature switch, if this is the case pull the molex wire off of the temperature switch and bypass

using a jumper wire. if your node lights work after doing this, just replace the temp. switch. you don,t

have to empty the coolant, just make sure the engine is cold before replacing it. good luck!

Mar 04, 2011 | 1993 Chevrolet K1500

2 Answers

2000 pontiac sunfire how to replace headlight bulb passenger [email protected]


two clips hold the headlight in place at the top...remove these and the headlamp will move forward enabling you to replace the halogen bulb (9007 at CTC)

Dec 09, 2009 | 1999 Pontiac Sunfire

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...