Valve clearance adjustment - Proton Cars & Trucks

Yes certainly can and the Service Manual as well

VALVE CLEARANCE (K3-VE)

VALVULITA https://www.valvulita.com > sites > default > files
(u) Apply engine oil to the cam of the camshaft and the journal part of the cylinder head, and then install the camshaft. NOTICE: Position it so the cam nose of ...
10 pages

Daihatsu TERIOS J100 Maintenance Manual (Page 18 of 43)

ManualsLib https://www.manualslib.com > ... > Maintenance manual
Inspection and adjustment of valve clearance. The measurement and adjustment ... apply engine oil to between the lock nut and the valve. rocker arm. q Remove ...

Tappet clearance 1300cc terios?

Fixya https://www.fixya.com > ... > Daihatsu > Terios
Nov 14, 2019 - The tappet clearance for your Hyundai Atos 2007 would be: ... Valve clearance Warm: 0.2 mm intake, 0.25 mm exhaust. ... Valve clearance Cold: 0.1 mm intake, 0.17 mm ...

I need valve clearance for Daihatsu Terios HC-EJ - Fixya
Jan 21, 2012
How do I set the valve clearances on a Daihatsu Terios 2001
Mar 1, 2015
Valve clearance and procedure for 1.2 Hc-Ej terios engine.it
Jun 3, 2014
Valve clearance for Daihatsu Terios - Fixya
Mar 20, 2012
More results from www.fixya.com

Approx 43.4249 ft-lb

The valve clearance specification for a Volvo FL10 truck depends on the specific engine model and year of manufacture. Generally, the valve clearance for the FL10 truck with a Volvo D10 engine should be checked and adjusted as follows: Remove the valve cover: Remove the valve cover to access the valves. Rotate the engine: Rotate the engine to the top dead center (TDC) position for the cylinder you want to adjust. Check the valve clearance: Use a feeler gauge to check the clearance between the valve stem and the rocker arm. The specification for the valve clearance should be listed in the engine service manual. Adjust the valve clearance: If the clearance is not within the specified range, adjust the clearance by loosening the lock nut on the rocker arm and turning the adjustment screw. Tighten the lock nut when the clearance is correct. Repeat for each cylinder: Repeat the above steps for each cylinder. Reinstall the valve cover: Once all the valve clearances have been checked and adjusted, reinstall the valve cover. It is recommended to refer to the engine service manual for specific instructions and specifications for your particular Volvo FL10 engine.

The valve clearance specification for a 1998 Hyundai H100 2.6 diesel bakkie is:
Intake valve clearance: 0.25 - 0.35 mm (0.010 - 0.014 in) Exhaust valve clearance: 0.45 - 0.55 mm (0.018 - 0.022 in)
The tappet setting for this engine will depend on the specific valve clearance measurements for each valve. If the valve clearances are found to be outside of the specification, the tappet settings will need to be adjusted accordingly. It is recommended to refer to the manufacturer's service manual for detailed instructions on how to perform the adjustment procedure.

The clearance, or gap, of the valves on a 2002 Mitsubishi Lancer OZ Rally is the distance between the valve and the valve seat when the valve is in the closed position. The clearance is typically specified by the manufacturer and is measured in thousandths of an inch.
To determine the valve clearance for your Lancer OZ Rally, you will need to refer to the manufacturer's specifications or service manual for your specific model. The valve clearance may vary depending on the type of engine and the specific application of the vehicle.
It is important to maintain the correct valve clearance on your Lancer OZ Rally to ensure that the engine operates efficiently and effectively. If the valve clearance is not within the specified range, it may cause problems such as reduced engine performance, increased fuel consumption, and increased emissions.
To adjust the valve clearance, you will need to remove the valve cover and use a feeler gauge to measure the gap between the valve and the valve seat. If the gap is not within the specified range, you will need to use a wrench to adjust the clearance by turning the adjustment screw on the rocker's arm. It is recommended that you have the valve clearance adjusted by a qualified mechanic if you are not familiar with this process.

Not all modern engines need you to set the valve clearances. Most engines use oil filled 'tappets' that self adjust the clearance as the oil temperature changes. Depending on which engine it is yours has a lot of the time you can only check the valve clearance but not adjust it.

The valve tappet clearance for the Mazda Bongo Brawny can vary depending on the specific engine model and year. Here are some general specifications for the different engine types: 2.0L FE engine: Intake valve clearance - 0.18-0.22mm, Exhaust valve clearance - 0.28-0.32mm 2.5L WL engine: Intake valve clearance - 0.20-0.25mm, Exhaust valve clearance - 0.30-0.35mm 2.5L RF engine: Intake valve clearance - 0.20-0.25mm, Exhaust valve clearance - 0.30-0.35mm It's important to note that the valve tappet clearance should be checked and adjusted by a qualified mechanic using the correct specifications and tools. Incorrect adjustment can cause engine damage and poor performance.

Valve clearance Google search your year make and model valve clearance. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Checking and adjusting valves
Engine Valve Adjustment Procedure The Right Way
Valve Clearance Adjustment
Valve clearance Google Search

Cummins M11

Intake valve clearance 0.010 inch
Exhaust valve clearance 0.024 inch

The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

Adjust the jet valve clearance before the adjustment of the
intake valve clearance.
Jet valve clearance (hot engine)
[Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

now adjust valve clearance
Valve clearance (hot engine) [Standard value]
Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)